[oe-commits] Steffen Sledz : linux-2.6.24: signal power on/ off to hipox machine board ctrl
git version control
git at git.openembedded.org
Tue Dec 1 09:03:13 UTC 2009
Module: openembedded.git
Branch: shr/merge
Commit: 199d2ea3a2ad8ece403ff6b529e11d6c6481603b
URL: http://gitweb.openembedded.net/?p=openembedded.git&a=commit;h=199d2ea3a2ad8ece403ff6b529e11d6c6481603b
Author: Steffen Sledz <sledz at dresearch.de>
Date: Tue Dec 1 07:42:26 2009 +0100
linux-2.6.24: signal power on/off to hipox machine board ctrl
Signed-off-by: Steffen Sledz <sledz at dresearch.de>
---
recipes/linux/linux-2.6.24/hipox/defconfig | 4 +-
.../linux/linux-2.6.24/hipox/hipox-OXE-INT2.patch | 188 ++++++++++++++++++++
recipes/linux/linux_2.6.24.bb | 1 +
3 files changed, 192 insertions(+), 1 deletions(-)
diff --git a/recipes/linux/linux-2.6.24/hipox/defconfig b/recipes/linux/linux-2.6.24/hipox/defconfig
index e5d0338..f2ef01a 100644
--- a/recipes/linux/linux-2.6.24/hipox/defconfig
+++ b/recipes/linux/linux-2.6.24/hipox/defconfig
@@ -1,7 +1,7 @@
#
# Automatically generated make config: don't edit
# Linux kernel version: 2.6.24.4
-# Tue Oct 20 14:36:38 2009
+# Fri Nov 27 16:35:59 2009
#
CONFIG_ARM=y
CONFIG_SYS_SUPPORTS_APM_EMULATION=y
@@ -177,6 +177,8 @@ CONFIG_ARCH_HIPOX_PCI_CLKOUT_2=y
CONFIG_ARCH_HIPOX_PCI_CLKOUT_3=y
CONFIG_HIPOX_PCI_RESET=y
CONFIG_HIPOX_PCI_RESET_GPIO=27
+CONFIG_HIPOX_OXE_INT2=y
+CONFIG_HIPOX_OXE_INT2_GPIO=34
# CONFIG_HIPOX_SATA_POWER_1 is not set
# CONFIG_HIPOX_SATA_POWER_2 is not set
CONFIG_FORCE_MAX_ZONEORDER=10
diff --git a/recipes/linux/linux-2.6.24/hipox/hipox-OXE-INT2.patch b/recipes/linux/linux-2.6.24/hipox/hipox-OXE-INT2.patch
new file mode 100644
index 0000000..372b139
--- /dev/null
+++ b/recipes/linux/linux-2.6.24/hipox/hipox-OXE-INT2.patch
@@ -0,0 +1,188 @@
+diff -Nurd linux-2.6.24.orig//arch/arm/mach-hipox/Kconfig linux-2.6.24/arch/arm/mach-hipox/Kconfig
+--- linux-2.6.24.orig//arch/arm/mach-hipox/Kconfig 2009-11-30 17:07:36.000000000 +0100
++++ linux-2.6.24/arch/arm/mach-hipox/Kconfig 2009-11-30 17:08:12.000000000 +0100
+@@ -241,6 +241,20 @@
+ reset of the SoC has emerged from reset. This defines the GPIO
+ line which is connected to the PCI reset
+
++config HIPOX_OXE_INT2
++ bool "Signal power state to HIPOX board controller"
++ default y
++ help
++ Signal power state to HIPOX board controller using OXE_INT2 signal.
++
++config HIPOX_OXE_INT2_GPIO
++ int "GPIO line using as power state signal to HIPOX board controller"
++ depends on HIPOX_OXE_INT2
++ default 34
++ help
++ This defines the GPIO used to signal power state to
++ HIPOX board controller.
++
+ config HIPOX_SATA_POWER_1
+ bool "Allow control of SATA 1 disk power via GPIO"
+ default n
+diff -Nurd linux-2.6.24.orig//arch/arm/mach-hipox/hipox.c linux-2.6.24/arch/arm/mach-hipox/hipox.c
+--- linux-2.6.24.orig//arch/arm/mach-hipox/hipox.c 2009-11-30 17:07:36.000000000 +0100
++++ linux-2.6.24/arch/arm/mach-hipox/hipox.c 2009-11-30 17:10:12.000000000 +0100
+@@ -47,6 +47,30 @@
+ #include <asm/arch/leon-early-prog.h>
+ #endif // CONFIG_LEON_START_EARLY
+
++#ifdef CONFIG_HIPOX_OXE_INT2_GPIO
++#if (CONFIG_HIPOX_OXE_INT2_GPIO < 32)
++#define OXE_INT2_NUM CONFIG_HIPOX_OXE_INT2_GPIO
++#define OXE_INT2_PRISEL_REG SYS_CTRL_GPIO_PRIMSEL_CTRL_0
++#define OXE_INT2_SECSEL_REG SYS_CTRL_GPIO_SECSEL_CTRL_0
++#define OXE_INT2_TERSEL_REG SYS_CTRL_GPIO_TERTSEL_CTRL_0
++#define OXE_INT2_QUASEL_REG SYS_CTRL_GPIO_PWMSEL_CTRL_0
++#define OXE_INT2_SET_OE_REG GPIO_A_OUTPUT_ENABLE_SET
++#define OXE_INT2_OUTPUT_SET_REG GPIO_A_OUTPUT_SET
++#define OXE_INT2_OUTPUT_CLR_REG GPIO_A_OUTPUT_CLEAR
++#else
++#define OXE_INT2_NUM ((CONFIG_HIPOX_OXE_INT2_GPIO) - 32)
++#define OXE_INT2_PRISEL_REG SYS_CTRL_GPIO_PRIMSEL_CTRL_1
++#define OXE_INT2_SECSEL_REG SYS_CTRL_GPIO_SECSEL_CTRL_1
++#define OXE_INT2_TERSEL_REG SYS_CTRL_GPIO_TERTSEL_CTRL_1
++#define OXE_INT2_QUASEL_REG SYS_CTRL_GPIO_PWMSEL_CTRL_1
++#define OXE_INT2_SET_OE_REG GPIO_B_OUTPUT_ENABLE_SET
++#define OXE_INT2_OUTPUT_SET_REG GPIO_B_OUTPUT_SET
++#define OXE_INT2_OUTPUT_CLR_REG GPIO_B_OUTPUT_CLEAR
++#endif
++
++#define OXE_INT2_MASK (1UL << (OXE_INT2_NUM))
++#endif // CONFIG_HIPOX_OXE_INT2_GPIO
++
+ #ifdef CONFIG_HIPOX_PCI_RESET_GPIO
+ #if (CONFIG_HIPOX_PCI_RESET_GPIO < 32)
+ #define PCI_RESET_NUM CONFIG_HIPOX_PCI_RESET_GPIO
+@@ -393,6 +417,22 @@
+ // Enable all DDR client interfaces
+ *(volatile u32*)DDR_BLKEN_REG |= (((1UL << DDR_BLKEN_CLIENTS_NUM_BITS) - 1) << DDR_BLKEN_CLIENTS_BIT);
+
++#ifdef CONFIG_HIPOX_OXE_INT2
++ printk("Enable OXE_INT2\n");
++
++ // Disable primary, secondary and teriary GPIO functions on OXE_INT2 line
++ writel(readl(OXE_INT2_PRISEL_REG) & ~OXE_INT2_MASK, OXE_INT2_PRISEL_REG);
++ writel(readl(OXE_INT2_SECSEL_REG) & ~OXE_INT2_MASK, OXE_INT2_SECSEL_REG);
++ writel(readl(OXE_INT2_TERSEL_REG) & ~OXE_INT2_MASK, OXE_INT2_TERSEL_REG);
++ writel(readl(OXE_INT2_QUASEL_REG) & ~OXE_INT2_MASK, OXE_INT2_QUASEL_REG);
++
++ // Enable GPIO output on OXE_INT2 line
++ writel(OXE_INT2_MASK, OXE_INT2_SET_OE_REG);
++
++ // Set OXE_INT2
++ writel(OXE_INT2_MASK, OXE_INT2_OUTPUT_SET_REG);
++#endif // CONFIG_HIPOX_OXE_INT2
++
+ #ifdef CONFIG_ARCH_HIPOX_UART1
+ // Block reset UART1
+ *(volatile u32*)SYS_CTRL_RSTEN_SET_CTRL = (1UL << SYS_CTRL_RSTEN_UART1_BIT);
+@@ -409,10 +449,10 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_1 |= 0x00000001;
+
+ // Setup GPIO line direction for UART1 SOUT
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x80000000;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x80000000;
+
+ // Setup GPIO line direction for UART1 SIN
+- *(volatile u32*)GPIO_B_OUTPUT_ENABLE_CLEAR |= 0x00000001;
++ *(volatile u32*)GPIO_B_OUTPUT_ENABLE_CLEAR = 0x00000001;
+
+ #ifdef CONFIG_ARCH_HIPOX_UART1_MODEM
+ // Route UART1 modem control lines onto external pins
+@@ -425,11 +465,11 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_1 |= 0x00000006;
+
+ // Setup GPIO line directions for UART1 modem control lines
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x08000000;
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR |= 0x70000000;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x08000000;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR = 0x70000000;
+
+- *(volatile u32*)GPIO_B_OUTPUT_ENABLE_SET |= 0x00000004;
+- *(volatile u32*)GPIO_B_OUTPUT_ENABLE_CLEAR |= 0x00000002;
++ *(volatile u32*)GPIO_B_OUTPUT_ENABLE_SET = 0x00000004;
++ *(volatile u32*)GPIO_B_OUTPUT_ENABLE_CLEAR = 0x00000002;
+ #endif // CONFIG_ARCH_HIPOX_UART1_MODEM
+
+ // Give Linux a contiguous numbering scheme for available UARTs
+@@ -448,8 +488,8 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_0 |= 0x00500000;
+
+ // Setup GPIO line directions for UART2 SIN/SOUT
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x00100000;
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR |= 0x00400000;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x00100000;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR = 0x00400000;
+
+ #ifdef CONFIG_ARCH_HIPOX_UART2_MODEM
+ // Route UART2 modem control lines onto external pins
+@@ -458,8 +498,8 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_0 |= 0x07800300;
+
+ // Setup GPIO line directions for UART2 modem control lines
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x02000200;
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR |= 0x05800100;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x02000200;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR = 0x05800100;
+ #endif // CONFIG_ARCH_HIPOX_UART2_MODEM
+
+ // Give Linux a contiguous numbering scheme for available UARTs
+@@ -478,8 +518,8 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_0 |= 0x000000C0;
+
+ // Setup GPIO line directions for UART3 SIN/SOUT
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x00000080;
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR |= 0x00000040;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x00000080;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR = 0x00000040;
+
+ // Enable UART3 interrupt
+ *(volatile u32*)SYS_CTRL_UART_CTRL |= (1UL << SYS_CTRL_UART3_IQ_EN);
+@@ -491,8 +531,8 @@
+ *(volatile u32*)SYS_CTRL_GPIO_TERTSEL_CTRL_0 |= 0x0000003f;
+
+ // Setup GPIO line directions for UART3 modem control lines
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET |= 0x00000030;
+- *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR |= 0x0000000f;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_SET = 0x00000030;
++ *(volatile u32*)GPIO_A_OUTPUT_ENABLE_CLEAR = 0x0000000f;
+ #endif // CONFIG_ARCH_HIPOX_UART3_MODEM
+
+ // Give Linux a contiguous numbering scheme for available UARTs
+@@ -1032,9 +1072,33 @@
+ }
+ #endif // CONFIG_HIPOX_LED_TEST
+
++static void hipox_poweroff(void)
++{
++ printk("Power off OXE810.\n");
++#ifdef CONFIG_HIPOX_OXE_INT2
++ printk("Disable OXE_INT2.\n");
++
++ // Disable primary, secondary and teriary GPIO functions on OXE_INT2 line
++ writel(readl(OXE_INT2_PRISEL_REG) & ~OXE_INT2_MASK, OXE_INT2_PRISEL_REG);
++ writel(readl(OXE_INT2_SECSEL_REG) & ~OXE_INT2_MASK, OXE_INT2_SECSEL_REG);
++ writel(readl(OXE_INT2_TERSEL_REG) & ~OXE_INT2_MASK, OXE_INT2_TERSEL_REG);
++ writel(readl(OXE_INT2_QUASEL_REG) & ~OXE_INT2_MASK, OXE_INT2_QUASEL_REG);
++
++ // Enable GPIO output on OXE_INT2 line
++ writel(OXE_INT2_MASK, OXE_INT2_SET_OE_REG);
++
++ // Reset OXE_INT2
++ writel(OXE_INT2_MASK, OXE_INT2_OUTPUT_CLR_REG);
++#endif // CONFIG_HIPOX_OXE_INT2
++}
++
+ static void __init hipox_init_machine(void)
+ {
+ //printk("hipox_init_machine()\n");
++
++ /* Register machine_poweroff */
++ pm_power_off = hipox_poweroff;
++
+ /* Initialise the spinlock used to make GPIO register set access atomic */
+ spin_lock_init(&hipox_gpio_spinlock);
+
diff --git a/recipes/linux/linux_2.6.24.bb b/recipes/linux/linux_2.6.24.bb
index ac7def5..381713c 100644
--- a/recipes/linux/linux_2.6.24.bb
+++ b/recipes/linux/linux_2.6.24.bb
@@ -104,6 +104,7 @@ SRC_URI_append_hipox = " \
file://hipox-ubifs.patch;patch=1 \
file://hipox-kconfig.patch;patch=1 \
file://hipox-sata-module.patch;patch=1 \
+ file://hipox-OXE-INT2.patch;patch=1 \
"
EXTRA_OEMAKE_smartq5 = " OBJCOPY=${OBJCOPY}"
More information about the Openembedded-commits
mailing list