[OE-core] Could we build tar-replacement firstly and not parallel if tar-replacement is needed to build

[Rongqing Li]

On 2012年08月07日 17:03, Richard Purdie wrote:
> On Tue, 2012-08-07 at 16:02 +0800, Rongqing Li wrote:
>>
>> On 2012年08月07日 15:41, Richard Purdie wrote:
>>> On Tue, 2012-08-07 at 13:59 +0800, Rongqing Li wrote:
>>>> Paste a RFC PATCH
>>>>
>>>> [RFC PATCH 1/1] bitbake: compile tar-replacement firstly, and not parallel
>>>>
>>>> Compiling tar-replacement or not is decided by version of host tar,
>>>> if the host tar version is lower than 1.23, Compiling tar-replacement
>>>> is needed.
>>>>
>>>> When doing popoluate tar-replacement sysroot to write the tar to
>>>> sysroot, but writing is not finished. other packages probably
>>>> use the being written tar to unzip file, which will lead to failure
>>>> and report the below error:
>>>> "bitbake_build/tmp/sysroots/x86_64-linux/usr/bin/tar: Text file busy"
>>>>
>>>> Now we compile tar-replacement firstly and not parallel to ensure
>>>> that a being written tar command will not be used.
>>>>
>>>> Signed-off-by: Roy.Li <rongqing.li at windriver.com>
>>>> ---
>>>>     scripts/bitbake |   14 +++++++++++++-
>>>>     1 files changed, 13 insertions(+), 1 deletions(-)
>>>>
>>>> diff --git a/scripts/bitbake b/scripts/bitbake
>>>> index 3772d82..eb6b144 100755
>>>> --- a/scripts/bitbake
>>>> +++ b/scripts/bitbake
>>>> @@ -134,7 +134,19 @@ if [ $buildpseudo -gt 0 ]; then
>>>>                 fi
>>>>             done
>>>>         done
>>>> -    bitbake pseudo-native $TARTARGET $additionalopts -c populate_sysroot
>>>> +
>>>> +    if [ $needtar = "1" ]; then
>>>> +       NUM_THREAD_LINE=`grep -n "^\s*BB_NUMBER_THREADS" conf/local.conf
>>>> |awk -F':' '{print $1}'`
>>>> +	test -n "$NUM_THREAD_LINE" &&
>>>> +	sed -i ''"$NUM_THREAD_LINE"'s/^\s*BB_NUMBER_THREADS/#\0/g' conf/local.conf
>>>> +
>>>> +	bitbake $TARTARGET -c populate_sysroot
>>>> +
>>>> +	test -n "$NUM_THREAD_LINE" &&
>>>> +	sed -i
>>>> ''"$NUM_THREAD_LINE"'s/^#\s*BB_NUMBER_THREADS/BB_NUMBER_THREADS/g'
>>>> conf/local.conf
>>>> +    fi
>>>
>>> We are *NOT* running sed over local.conf. What is the user used a
>>> different configuration file for example?
>>
>> I use the sed to disable NUM_THREAD_LINE in conf/local.conf if
>> NUM_THREAD_LINE has been enabled.
>>
>> After compile $TARTARGET, use the sed to enable NUM_THREAD_LINE
>> in conf/local.conf
>
> I understand what you did, I just don't want to do this. Its horrible
> and buggy.
>
>>> If you're just building tar-native, is there a parallel race possible?
>>> I'm not sure that there is?
>>
>> Even if I just build tar-native, I still have several packages which
>> are needed to building.
>>
>>
>> $bitbake tar-replacement-native -g
>>
>> $ cat pn-buildlist
>> autoconf-native
>> libtool-native
>> m4-native
>> gettext-minimal-native
>> tar-replacement-native
>> quilt-native
>> gnu-config-native
>> automake-native
>
> but tar-replacement-native will not build until all the above have
> executed their populate_sysroot tasks, correct?
>
> So I don't see a task that would run at the same time as
> tar-replacement:do_populate_sysroot which will be the last task to run?
>
> Cheers,
>
> Richard
>
>


You are right, seems I only need to build tar-replacement firstly, donot
need to disable the BB_NUMBER_THREADS.


-Roy



>

-- 
Best Reagrds,
Roy | RongQing Li