<div dir="ltr"><div><div><div>Hello,<br><br></div>I add ti-meta but capemgr is not work<br><br></div>This my boot log<br><br>Booting from mmc ...<br>## Booting kernel from Legacy Image at 80007fc0 ...<br> Image Name: Linux-3.14.0-yocto-standard<br>
Image Type: ARM Linux Kernel Image (uncompressed)<br> Data Size: 4985304 Bytes = 4.8 MiB<br> Load Address: 80008000<br> Entry Point: 80008000<br> Verifying Checksum ... OK<br>## Flattened Device Tree blob at 80f80000<br>
Booting using the fdt blob at 0x80f80000<br> XIP Kernel Image ... OK<br>OK<br> Using Device Tree in place at 80f80000, end 80f8a207<br><br>Starting kernel ...<br><br>Booting Linux on physical CPU 0x0<br>Initializing cgroup subsys cpuset<br>
Initializing cgroup subsys cpu<br>Initializing cgroup subsys cpuacct<br>Linux version 3.14.0-yocto-standard (panda@pandabook) (gcc version 4.8.2 (GCC) ) #1 PREEMPT Fri Jun 27 15:16:56 EEST 2014<br>CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d<br>
CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache<br>Machine model: TI AM335x BeagleBone<br>cma: CMA: reserved 16 MiB at 9e800000<br>Memory policy: Data cache writeback<br>CPU: All CPU(s) started in SVC mode.<br>
AM335X ES2.1 (sgx neon )<br>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 129792<br>Kernel command line: console=ttyO0,115200n8 root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait<br>PID hash table entries: 2048 (order: 1, 8192 bytes)<br>
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)<br>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)<br>allocated 1048576 bytes of page_cgroup<br>please try 'cgroup_disable=memory' option if you don't want memory cgroups<br>
Memory: 489448K/523264K available (7491K kernel code, 520K rwdata, 2444K rodata, 488K init, 757K bss, 33816K reserved, 0K highmem)<br>Virtual kernel memory layout:<br> vector : 0xffff0000 - 0xffff1000 ( 4 kB)<br> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)<br>
vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)<br> lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)<br> pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)<br> modules : 0xbf000000 - 0xbfe00000 ( 14 MB)<br> .text : 0xc0008000 - 0xc09bc044 (9937 kB)<br>
.init : 0xc09bd000 - 0xc0a37034 ( 489 kB)<br> .data : 0xc0a38000 - 0xc0aba0d4 ( 521 kB)<br> .bss : 0xc0aba0d4 - 0xc0b77678 ( 758 kB)<br>SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1<br>
Preemptible hierarchical RCU implementation.<br>NR_IRQS:16 nr_irqs:16 16<br>IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts<br>Total of 128 interrupts on 1 active controller<br>OMAP clockevent source: timer2 at 24000000 Hz<br>
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns<br>OMAP clocksource: timer1 at 24000000 Hz<br>Console: colour dummy device 80x30<br>Calibrating delay loop... 548.86 BogoMIPS (lpj=2744320)<br>pid_max: default: 32768 minimum: 301<br>
Security Framework initialized<br>Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)<br>Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)<br>Initializing cgroup subsys debug<br>Initializing cgroup subsys memory<br>
Initializing cgroup subsys devices<br>Initializing cgroup subsys freezer<br>Initializing cgroup subsys net_cls<br>Initializing cgroup subsys blkio<br>CPU: Testing write buffer coherency: ok<br>ftrace: allocating 25107 entries in 74 pages<br>
Setting up static identity map for 0x806c4000 - 0x806c4058<br>devtmpfs: initialized<br>VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3<br>omap_hwmod: tptc0 using broken dt data from edma<br>omap_hwmod: tptc1 using broken dt data from edma<br>
omap_hwmod: tptc2 using broken dt data from edma<br>omap_hwmod: debugss: _wait_target_disable failed<br>xor: measuring software checksum speed<br> arm4regs : 685.200 MB/sec<br> 8regs : 504.800 MB/sec<br> 32regs : 658.800 MB/sec<br>
xor: using function: arm4regs (685.200 MB/sec)<br>pinctrl core: initialized pinctrl subsystem<br>regulator-dummy: no parameters<br>NET: Registered protocol family 16<br>DMA: preallocated 256 KiB pool for atomic coherent allocations<br>
cpuidle: using governor ladder<br>cpuidle: using governor menu<br>platform 49000000.edma: alias fck already exists<br>platform 49000000.edma: alias fck already exists<br>platform 49000000.edma: alias fck already exists<br>
OMAP GPIO hardware version 0.1<br>hw-breakpoint: debug architecture 0x4 unsupported.<br>bio: create slab <bio-0> at 0<br>raid6: int32x1 89 MB/s<br>raid6: int32x2 107 MB/s<br>raid6: int32x4 90 MB/s<br>raid6: int32x8 92 MB/s<br>
raid6: using algorithm int32x2 (107 MB/s)<br>raid6: using intx1 recovery algorithm<br>edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver<br>vmmcsd_fixed: 3300 mV <br>SCSI subsystem initialized<br>usbcore: registered new interface driver usbfs<br>
usbcore: registered new interface driver hub<br>usbcore: registered new device driver usb<br>omap_i2c 44e0b000.i2c: could not find pctldev for node /pinmux@44e10800/pinmux_i2c0_pins, deferring probe<br>platform 44e0b000.i2c: Driver omap_i2c requests probe deferral<br>
cfg80211: Calling CRDA to update world regulatory domain<br>Switched to clocksource timer1<br>NET: Registered protocol family 2<br>TCP established hash table entries: 4096 (order: 2, 16384 bytes)<br>TCP bind hash table entries: 4096 (order: 2, 16384 bytes)<br>
TCP: Hash tables configured (established 4096 bind 4096)<br>TCP: reno registered<br>UDP hash table entries: 256 (order: 0, 4096 bytes)<br>UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)<br>NET: Registered protocol family 1<br>
RPC: Registered named UNIX socket transport module.<br>RPC: Registered udp transport module.<br>RPC: Registered tcp transport module.<br>RPC: Registered tcp NFSv4.1 backchannel transport module.<br>hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available<br>
futex hash table entries: 256 (order: -1, 3072 bytes)<br>NFS: Registering the id_resolver key type<br>Key type id_resolver registered<br>Key type id_legacy registered<br>msgmni has been set to 987<br>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)<br>
io scheduler noop registered<br>io scheduler deadline registered<br>io scheduler cfq registered (default)<br>pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568<br>omap_uart 44e09000.serial: no wakeirq for uart0<br>
44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88, base_baud = 3000000) is a OMAP UART0<br>console [ttyO0] enabled<br>[drm] Initialized drm 1.1.0 20060810<br>brd: module loaded<br>mtdoops: mtd device (mtddev=name/number) must be supplied<br>
usbcore: registered new interface driver kaweth<br>pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver<br>usbcore: registered new interface driver pegasus<br>usbcore: registered new interface driver rtl8150<br>
usbcore: registered new interface driver asix<br>usbcore: registered new interface driver ax88179_178a<br>usbcore: registered new interface driver cdc_ether<br>usbcore: registered new interface driver dm9601<br>usbcore: registered new interface driver smsc75xx<br>
usbcore: registered new interface driver smsc95xx<br>usbcore: registered new interface driver net1080<br>usbcore: registered new interface driver cdc_subset<br>usbcore: registered new interface driver zaurus<br>usbcore: registered new interface driver MOSCHIP usb-ethernet driver<br>
usbcore: registered new interface driver int51x1<br>usbcore: registered new interface driver cdc_ncm<br>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver<br>ehci-omap: OMAP-EHCI Host Controller driver<br>
usbcore: registered new interface driver usb-storage<br>mousedev: PS/2 mouse device common for all mice<br>omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0<br>i2c /dev entries driver<br>omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec<br>
48060000.mmc supply vmmc_aux not found, using dummy regulator<br>481d8000.mmc supply vmmc_aux not found, using dummy regulator<br>usbcore: registered new interface driver usbhid<br>usbhid: USB HID core driver<br>oprofile: using arm/armv7<br>
u32 classifier<br> Actions configured<br>TCP: cubic registered<br>NET: Registered protocol family 10<br>sit: IPv6 over IPv4 tunneling driver<br>NET: Registered protocol family 17<br>mmc0: host does not support reading read-only switch. assuming write-enable.<br>
Key type dns_resolver registered<br>ThumbEE CPU extension supported.<br>mmc0: new high speed SDHC card at address 0001<br>bio: create slab <bio-1> at 1<br>mmcblk0: mmc0:0001 ASTC 7.38 GiB <br> mmcblk0: p1 p2<br>Btrfs loaded<br>
regulator-dummy: disabling<br>slave hdmi.6: could not get i2c<br>platform hdmi.6: Driver slave requests probe deferral<br>platform 4830e000.lcdc: Driver tilcdc requests probe deferral<br>DCDC1: at 1500 mV <br>vdd_mpu: 925 <--> 1325 mV at 1100 mV <br>
vdd_core: 925 <--> 1150 mV at 1100 mV <br>LDO1: at 1800 mV <br>LDO2: at 3300 mV <br>LDO3: 1800 mV <br>LDO4: at 3300 mV <br>tps65217 0-0024: TPS65217 ID 0xe version 1.2<br>omap_i2c 44e0b000.i2c: bus 0 rev0.11 at 400 kHz<br>
mmc1: BKOPS_EN bit is not set<br>mmc1: new high speed MMC card at address 0001<br>mmcblk1: mmc1:0001 MMC02G 1.78 GiB <br>mmcblk1boot0: mmc1:0001 MMC02G partition 1 1.00 MiB<br>mmcblk1boot1: mmc1:0001 MMC02G partition 2 1.00 MiB<br>
mmcblk1: p1 p2<br> mmcblk1boot1: unknown partition table<br> mmcblk1boot0: unknown partition table<br>tilcdc 4830e000.lcdc: found TDA19988<br>[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).<br>[drm] No driver support for vblank timestamp query.<br>
tilcdc 4830e000.lcdc: No connectors reported connected with modes<br>[drm] Cannot find any crtc or sizes - going 1024x768<br>Console: switching to colour frame buffer device 128x48<br>tilcdc 4830e000.lcdc: fb0: frame buffer device<br>
tilcdc 4830e000.lcdc: registered panic notifier<br>[drm] Initialized tilcdc 1.0.0 20121205 on minor 0<br>console [netcon0] enabled<br>netconsole: network logging started<br>davinci_mdio 4a101000.mdio: davinci mdio revision 1.6<br>
davinci_mdio 4a101000.mdio: detected phy mask fffffffe<br>libphy: 4a101000.mdio: probed<br>davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720<br>Detected MACID = 1c:ba:8c:f1:ec:e4<br>
omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)<br>EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)<br>VFS: Mounted root (ext4 filesystem) readonly on device 179:2.<br>
devtmpfs: mounted<br>Freeing unused kernel memory: 488K (c09bd000 - c0a37000)<br>INIT: version 2.88 booting<br>Starting udev<br>udevd[82]: starting version 182<br>EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended<br>
EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)<br>Starting Bootlog daemon: bootlogd.<br>random: dd urandom read with 128 bits of entropy available<br>random: nonblocking pool is initialized<br>Mon Jun 30 07:45:00 UTC 2014<br>
INIT: Entering runlevel: 5<br>Configuring network interfaces... net eth0: initializing cpsw version 1.12 (0)<br>net eth0: phy found : id is : 0x7c0f1<br>libphy: PHY 4a101000.mdio:01 not found<br>net eth0: phy 4a101000.mdio:01 not found on slave 1<br>
IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready<br>udhcpc (v1.22.1) started<br>Sending discover...<br>libphy: 4a101000.mdio:00 - Link is Up - 100/Full<br>IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready<br>Sending discover...<br>
Sending select for 192.168.50.1<br>Lease of 192.168.50.18 obtained, lease time 691200<br>/etc/udhcpc.d/50default: Adding DNS 192.168.50.1<br>/etc/udhcpc.d/50default: Adding DNS 192.168.50.1<br>done.<br>Starting OpenBSD Secure Shell server: sshd<br>
done.<br>Starting syslogd/klogd: done<br>Stopping Bootlog daemon: bootlogd.<br><br>Poky (Yocto Project Reference Distro) 1.6.1 beaglebone /dev/ttyO0<br><br></div>I run this command <br><br>root@beaglebone:~# cape-stop.sh <br>
hexdump: /sys/bus/i2c/devices/3-005*/eeprom: No such file or directory<br>unknown cape: <br><br><div><br></div></div><div class="gmail_extra"><br><br><div class="gmail_quote">2014-06-30 11:15 GMT+03:00 Anders Darander <span dir="ltr"><<a href="mailto:anders@chargestorm.se" target="_blank">anders@chargestorm.se</a>></span>:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">* Robert Yang <<a href="mailto:liezhi.yang@windriver.com">liezhi.yang@windriver.com</a>> [140630 05:47]:<br>
<div><div class="h5"><br>
<br>
> On 06/30/2014 12:24 AM, Life Life wrote:<br>
> > Hello,<br>
<br>
> > I'm trying build yocto based linux, My hardware is beaglebone black I<br>
> > successfull build system image. But I can't see capemanager. Beacuse my lcd is<br>
> > not work.<br>
<br>
> Hello,<br>
<br>
> The cape manager is in meta-ti layer:<br>
<br>
> <a href="http://layers.openembedded.org/layerindex/branch/master/layer/meta-ti/" target="_blank">http://layers.openembedded.org/layerindex/branch/master/layer/meta-ti/</a><br>
<br>
> Seems that we'd better add it to meta-yoco-bsp ?<br>
<br>
</div></div>Unless something has changed since I last looked at this, I don't think<br>
so.<br>
<br>
If I remember correctly, capemgr basically consists of a number of<br>
patches not in the mainline kernel (and also not in TI's staging<br>
kernel). I haven't checked it, by I doubt that we have them in the<br>
linux-yocto kernel. (Especially as the last time I checked it, you had<br>
to revert to a 3.8 (if I rember correctly, it might have been an even<br>
earlier kernel) kernel to get full capemgr support.<br>
<br>
If this has changed, then it'd be interesting to know!<br>
<br>
Cheers,<br>
Anders<br>
<div class="HOEnZb"><div class="h5"><br>
> Add Saul in the loop.<br>
<br>
<br>
</div></div><span class="HOEnZb"><font color="#888888">--<br>
Anders Darander<br>
ChargeStorm AB / eStorm AB<br>
--<br>
_______________________________________________<br>
Openembedded-core mailing list<br>
<a href="mailto:Openembedded-core@lists.openembedded.org">Openembedded-core@lists.openembedded.org</a><br>
<a href="http://lists.openembedded.org/mailman/listinfo/openembedded-core" target="_blank">http://lists.openembedded.org/mailman/listinfo/openembedded-core</a><br>
</font></span></blockquote></div><br></div>