<div dir="ltr">Hi,<div>I am using OpenBMC-1.0 (phosphor).<br>On an AST2500-based board, the boot-logs get stuck at </div><div><b><span style="font-size:11pt;font-family:Calibri,sans-serif"> Uncompressing Linux… done, booting the kernel.</span></b></div><div><font face="Calibri, sans-serif"><span style="font-size:14.6667px"><b><br clear="all"></b></span></font><div><div data-smartmail="gmail_signature"><div dir="ltr">The u-boot uses the correct UART console because its logs are displayed.<br>But after that, the kernel boot logs are not seen. I am sure it is booting, but the problem is that the kernel seems to be configured to use the wrong serial console.<br>I tried changing the <i>'device' </i>variable in obmc-console.conf from <i>device=ttyS5 </i> to different values, but it's no use.<br>Could someone please suggest how to make the kernel boot logs be displayed on the correct UART?</div><div dir="ltr"><br></div><div dir="ltr">------------------------------------------- FYI the boot logs: -----------------------------------------</div><div><br><div>DRAM Init-V0B-DDR4</div><div>0abc1-4Gb-Done</div><div>Read margin-DL:0.3509/DH:0.3803 CK (min:0.35)</div><div><br></div><div><br></div><div>U-Boot 2016.05 (Jul 06 2016 - 17:22:40 +0100)</div><div><br></div><div>DRAM: 496 MiB</div><div>Flash: 32 MiB</div><div>*** Warning - bad CRC, using default environment</div><div><br></div><div>In: serial</div><div>Out: serial</div><div>Err: serial</div><div>Net: MAC0 : RGMII </div><div>MAC1 : RGMII </div><div>FTGMAC100#0</div><div>Error: FTGMAC100#0 address not set.</div><div>, FTGMAC100#1</div><div>Error: FTGMAC100#1 address not set.</div><div><br></div><div>Hit any key to stop autoboot: 0 </div><div>## Booting kernel from Legacy Image at 20080000 ...</div><div> Image Name: Phosphor OpenBMC (Phosphor OpenB</div><div> Image Type: ARM Linux Kernel Image (uncompressed)</div><div> Data Size: 2004098 Bytes = 1.9 MiB</div><div> Load Address: 80001000</div><div> Entry Point: 80001000</div><div> Verifying Checksum ... OK</div><div>## Loading init Ramdisk from Legacy Image at 20300000 ...</div><div> Image Name: obmc-phosphor-image</div><div> Image Type: ARM Linux RAMDisk Image (lzma compressed)</div><div> Data Size: 1670931 Bytes = 1.6 MiB</div><div> Load Address: 81000000</div><div> Entry Point: 81000000</div><div> Verifying Checksum ... OK</div><div> Loading Kernel Image ... OK</div><div><br></div><div>Starting kernel ...</div><div><br></div><div>Uncompressing Linux... done, booting the kernel.</div><div>-------------------------------------------------------------------------------------------------------</div><br></div><div>Thanks,<br><i><b>Basil Varghese</b></i><br></div></div></div></div><div><div class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div><div dir="ltr"><div><div dir="ltr"><div><i>______________________________________</i></div></div></div></div></div></div></div></div>
</div>