[oe] loading jffs2 image on arm926ek board

Tue Aug 17 09:38:53 UTC 2010

Hello,

I have used openembedded   to build rfs image with x libraries for arm926ek
board.

After loading the image i got following error:

bootm 0x20000000
## Booting image at 20000000 ...
   Image Name:   Linux-2.6.32.9
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1392284 Bytes =  1.3 MB
   Load Address: 20008000
   Entry Point:  20008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing
Linux..........................................................................................
done, booting the kernel.
Linux version 2.6.32.9 (root at Nakshatra) (gcc version 4.2.2) #14 Fri Apr 9
16:01:58 NPT 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91SAM9261-EK
Ignoring unrecognised tag 0x54410008
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 198 MHz, master 99 MHz, main 18.432 MHz
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: mem=128M console=ttyS0,115200 rootfstype=jffs2
root=/dev/mtdblock0 rw init=/bin/sh
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126932KB available (2520K code, 184K data, 124K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:192
AT91: 96 gpio irqs in 3 banks
Console: colour dummy device 80x30
console [ttyS0] enabled
Calibrating delay loop... 99.12 BogoMIPS (lpj=495616)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource pit
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 248
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered (default)
atmel_lcdfb atmel_lcdfb.0: backlight control is not available
atmel_lcdfb atmel_lcdfb.0: 600KiB frame buffer at 27900000 (mapped at
ffc00000)
Console: switching to colour frame buffer device 80x30
atmel_lcdfb atmel_lcdfb.0: fb0: Atmel LCDC at 0x00600000 (mapped at
c885a000), irq 21
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffb0000 (irq = 6) is a ATMEL_SERIAL
atmel_usart.2: ttyS2 at MMIO 0xfffb4000 (irq = 7) is a ATMEL_SERIAL
atmel_usart.3: ttyS3 at MMIO 0xfffb8000 (irq = 8) is a ATMEL_SERIAL
brd: module loaded
NAND device: Manufacturer ID: 0x20, Chip ID: 0xda (ST Micro NAND 256MiB 3,3V
8-bit)
AT91 NAND: 8-bit, Software ECC
Scanning device for bad blocks
Bad eraseblock 56 at 0x000000700000
Bad eraseblock 1909 at 0x00000eea0000
Creating 2 MTD partitions on "atmel_nand":
0x000000000000-0x000008000000 : "Partition 1"
0x000008000000-0x000010000000 : "Partition 2"
atmel_spi atmel_spi.0: Atmel SPI Controller at 0xfffc8000 (irq 12)
dm9000 Ethernet Driver, V1.31
dm9000 dm9000.0: read wrong id 0x342a0028
dm9000 dm9000.0: read wrong id 0x2b2a0000
dm9000 dm9000.0: read wrong id 0x2b2a0028
dm9000 dm9000.0: read wrong id 0x342a0028
dm9000 dm9000.0: read wrong id 0x2b2a0028
dm9000 dm9000.0: read wrong id 0x2b2a2928
dm9000 dm9000.0: read wrong id 0x2b2a0028
dm9000 dm9000.0: read wrong id 0x2b002928
dm9000 dm9000.0: wrong id: 0x2b002928
dm9000 dm9000.0: not found (-19).
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 20, io mem 0x00500000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN
adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
ads7846 spi0.2: touchscreen, irq 29
input: ADS7843 Touchscreen as
/devices/platform/atmel_spi.0/spi0.2/input/input0
i2c /dev entries driver
TCP cubic registered
NET: Registered protocol family 17
usb 1-1: new full speed USB device using at91_ohci and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
VFS: Mounted root (jffs2 filesystem) on device 31:0.
Freeing init memory: 124K
Kernel panic - not syncing: Attempted to kill init!
Backtrace:
[<c002b40c>] (dump_backtrace+0x0/0x10c) from [<c002b54c>]
(dump_stack+0x18/0x1c)
 r6:00000004 r5:c7815c40 r4:c02b9d8c
[<c002b534>] (dump_stack+0x0/0x1c) from [<c003e43c>] (panic+0x4c/0x134)
[<c003e3f0>] (panic+0x0/0x134) from [<c0041278>] (do_exit+0x64/0x5b0)
 r3:c02a56b4 r2:c7815d60 r1:c7819d20 r0:c0266378
[<c0041214>] (do_exit+0x0/0x5b0) from [<c0041854>] (do_group_exit+0x90/0xc4)
[<c00417c4>] (do_group_exit+0x0/0xc4) from [<c004b0f4>]
(get_signal_to_deliver+0x2e0/0x318)
 r4:00000004
[<c004ae14>] (get_signal_to_deliver+0x0/0x318) from [<c002a104>]
(do_notify_resume+0x60/0x578)
[<c002a0a4>] (do_notify_resume+0x0/0x578) from [<c0027ea8>]
(work_pending+0x1c/0x20)

Kindly guide,
rani