[oe] [meta-handheld][PATCH 3/3] linux-yocto-dev: remove development 3.14 kernel recipe
Andrea Adami
andrea.adami at gmail.com
Wed May 21 21:26:22 UTC 2014
The machines using it before are now preferring linux-yocto.
Signed-off-by: Andrea Adami <andrea.adami at gmail.com>
---
recipes-kernel/linux/linux-yocto-dev.bbappend | 37 --
...-s3c24xx-DMA-don-t-use-autoreload-feature.patch | 683 ---------------------
.../h1940/0002-s3cmci-minor-fixups.patch | 40 --
...10-drop-RFKILL-driver-for-H1940-bluetooth.patch | 200 ------
...mtd-nand-s3c2410-add-iPAQ-specific-layout.patch | 28 -
...005-ARM-s3c2410-Add-nand-device-for-h1940.patch | 114 ----
...006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch | 41 --
...-ARM-s3c2410-unlock-reset-button-on-H1940.patch | 49 --
...08-ARM-h1940-add-bluetooth-RF-kill-switch.patch | 75 ---
.../h1940/0009-rfkill-add-IR-type.patch | 51 --
...fkill_gpio-add-support-for-inverted-GPIOs.patch | 59 --
.../h1940/0011-ARM-h1940-add-IR-switch.patch | 61 --
...012-ARM-h1940-increase-oversampling-shift.patch | 29 -
.../linux/linux-yocto-dev/h1940/defconfig | 200 ------
14 files changed, 1667 deletions(-)
delete mode 100644 recipes-kernel/linux/linux-yocto-dev.bbappend
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0001-s3c24xx-DMA-don-t-use-autoreload-feature.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0002-s3cmci-minor-fixups.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0003-ARM-s3c2410-drop-RFKILL-driver-for-H1940-bluetooth.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0004-mtd-nand-s3c2410-add-iPAQ-specific-layout.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0005-ARM-s3c2410-Add-nand-device-for-h1940.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0007-ARM-s3c2410-unlock-reset-button-on-H1940.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0008-ARM-h1940-add-bluetooth-RF-kill-switch.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0009-rfkill-add-IR-type.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0010-rfkill_gpio-add-support-for-inverted-GPIOs.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0011-ARM-h1940-add-IR-switch.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/0012-ARM-h1940-increase-oversampling-shift.patch
delete mode 100644 recipes-kernel/linux/linux-yocto-dev/h1940/defconfig
diff --git a/recipes-kernel/linux/linux-yocto-dev.bbappend b/recipes-kernel/linux/linux-yocto-dev.bbappend
deleted file mode 100644
index 4594c6d..0000000
--- a/recipes-kernel/linux/linux-yocto-dev.bbappend
+++ /dev/null
@@ -1,37 +0,0 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}-dev:${THISDIR}/${PN}:${THISDIR}/files:"
-
-COMPATIBLE_MACHINE .= "|h1940"
-
-# Override kernel features
-#KERNEL_EXTRA_FEATURES ?= "features/netfilter/netfilter.scc"
-
-KERNEL_EXTRA_FEATURES_h1940 ?= ""
-KMACHINE_h1940 = "h1940"
-
-# Note: Providing "defconfig" we bypass the linux-yocto processing
-# re-expand the defconfig produced by "make_savedefconfig"
-KCONFIG_MODE_h1940 = "--alldefconfig"
-
-SRC_URI_append_h1940 = " \
- file://defconfig \
- file://0001-s3c24xx-DMA-don-t-use-autoreload-feature.patch \
- file://0002-s3cmci-minor-fixups.patch \
- file://0003-ARM-s3c2410-drop-RFKILL-driver-for-H1940-bluetooth.patch \
- file://0008-ARM-h1940-add-bluetooth-RF-kill-switch.patch \
- file://0004-mtd-nand-s3c2410-add-iPAQ-specific-layout.patch \
- file://0005-ARM-s3c2410-Add-nand-device-for-h1940.patch \
- file://0006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch \
- file://0009-rfkill-add-IR-type.patch \
- file://0007-ARM-s3c2410-unlock-reset-button-on-H1940.patch \
- file://0010-rfkill_gpio-add-support-for-inverted-GPIOs.patch \
- file://0011-ARM-h1940-add-IR-switch.patch \
- file://0012-ARM-h1940-increase-oversampling-shift.patch \
- file://qvga/logo_linux_clut224.ppm.bz2 \
- "
-
-do_configure_prepend() {
-
- if [ -e ${WORKDIR}/logo_linux_clut224.ppm ]; then
- install -m 0644 ${WORKDIR}/logo_linux_clut224.ppm ${WORKDIR}/linux/drivers/video/logo/logo_linux_clut224.ppm
- fi
-}
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0001-s3c24xx-DMA-don-t-use-autoreload-feature.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0001-s3c24xx-DMA-don-t-use-autoreload-feature.patch
deleted file mode 100644
index 4123823..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0001-s3c24xx-DMA-don-t-use-autoreload-feature.patch
+++ /dev/null
@@ -1,683 +0,0 @@
-From 9befdde54ce7e5e45303fb68eb941442ff6d7c9e Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:05:05 +0300
-Subject: [PATCH 01/12] s3c24xx: DMA: don't use autoreload feature
-
-Some integrated DMA-capable hardware doesn't like autoreload
-feature of s3c24xx DMA-engine, that's why s3cmci driver
-didn't work with DMA transfers enabled.
-
-I rewrote DMA driver not to use autoreload feature and removed
-all pre-loading features. Buffer re-load is fast enought to perform
-it in IRQ handler, and anyway I don't see any reason to waste CPU
-cycles on waiting for buffer load. Driver is much simplier now,
-it was tested with s3cmci and s3c24xx-i2s drivers on s3c2442 and
-s3c2410 SoCs and works just nice
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/dma.c | 445 +++++--------------------------
- arch/arm/mach-s3c24xx/include/mach/dma.h | 15 +-
- 2 files changed, 71 insertions(+), 389 deletions(-)
-
-diff --git a/arch/arm/mach-s3c24xx/dma.c b/arch/arm/mach-s3c24xx/dma.c
-index 4a65cba..adbcb91 100644
---- a/arch/arm/mach-s3c24xx/dma.c
-+++ b/arch/arm/mach-s3c24xx/dma.c
-@@ -131,70 +131,6 @@ dmadbg_showregs(const char *fname, int line, struct s3c2410_dma_chan *chan)
- #define dbg_showchan(chan) do { } while(0)
- #endif /* CONFIG_S3C2410_DMA_DEBUG */
-
--/* s3c2410_dma_stats_timeout
-- *
-- * Update DMA stats from timeout info
--*/
--
--static void
--s3c2410_dma_stats_timeout(struct s3c2410_dma_stats *stats, int val)
--{
-- if (stats == NULL)
-- return;
--
-- if (val > stats->timeout_longest)
-- stats->timeout_longest = val;
-- if (val < stats->timeout_shortest)
-- stats->timeout_shortest = val;
--
-- stats->timeout_avg += val;
--}
--
--/* s3c2410_dma_waitforload
-- *
-- * wait for the DMA engine to load a buffer, and update the state accordingly
--*/
--
--static int
--s3c2410_dma_waitforload(struct s3c2410_dma_chan *chan, int line)
--{
-- int timeout = chan->load_timeout;
-- int took;
--
-- if (chan->load_state != S3C2410_DMALOAD_1LOADED) {
-- printk(KERN_ERR "dma%d: s3c2410_dma_waitforload() called in loadstate %d from line %d\n", chan->number, chan->load_state, line);
-- return 0;
-- }
--
-- if (chan->stats != NULL)
-- chan->stats->loads++;
--
-- while (--timeout > 0) {
-- if ((dma_rdreg(chan, S3C2410_DMA_DSTAT) << (32-20)) != 0) {
-- took = chan->load_timeout - timeout;
--
-- s3c2410_dma_stats_timeout(chan->stats, took);
--
-- switch (chan->load_state) {
-- case S3C2410_DMALOAD_1LOADED:
-- chan->load_state = S3C2410_DMALOAD_1RUNNING;
-- break;
--
-- default:
-- printk(KERN_ERR "dma%d: unknown load_state in s3c2410_dma_waitforload() %d\n", chan->number, chan->load_state);
-- }
--
-- return 1;
-- }
-- }
--
-- if (chan->stats != NULL) {
-- chan->stats->timeout_failed++;
-- }
--
-- return 0;
--}
--
- /* s3c2410_dma_loadbuffer
- *
- * load a buffer, and update the channel state
-@@ -204,66 +140,33 @@ static inline int
- s3c2410_dma_loadbuffer(struct s3c2410_dma_chan *chan,
- struct s3c2410_dma_buf *buf)
- {
-- unsigned long reload;
--
- if (buf == NULL) {
- dmawarn("buffer is NULL\n");
- return -EINVAL;
- }
-
-- pr_debug("s3c2410_chan_loadbuffer: loading buff %p (0x%08lx,0x%06x)\n",
-+ pr_debug("%s: loading buff %p (0x%08lx,0x%06x)\n", __func__,
- buf, (unsigned long)buf->data, buf->size);
-
- /* check the state of the channel before we do anything */
-
-- if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
-- dmawarn("load_state is S3C2410_DMALOAD_1LOADED\n");
-- }
--
-- if (chan->load_state == S3C2410_DMALOAD_1LOADED_1RUNNING) {
-- dmawarn("state is S3C2410_DMALOAD_1LOADED_1RUNNING\n");
-- }
-+ if (chan->load_state != S3C2410_DMALOAD_NONE)
-+ printk(KERN_ERR "dma%d: channel already has buffer loaded\n",
-+ chan->number);
-
-- /* it would seem sensible if we are the last buffer to not bother
-- * with the auto-reload bit, so that the DMA engine will not try
-- * and load another transfer after this one has finished...
-- */
-- if (chan->load_state == S3C2410_DMALOAD_NONE) {
-- pr_debug("load_state is none, checking for noreload (next=%p)\n",
-- buf->next);
-- reload = (buf->next == NULL) ? S3C2410_DCON_NORELOAD : 0;
-- } else {
-- //pr_debug("load_state is %d => autoreload\n", chan->load_state);
-- reload = S3C2410_DCON_AUTORELOAD;
-- }
--
-- if ((buf->data & 0xf0000000) != 0x30000000) {
-+ if ((buf->data & 0xf0000000) != 0x30000000)
- dmawarn("dmaload: buffer is %p\n", (void *)buf->data);
-- }
-
- writel(buf->data, chan->addr_reg);
-
- dma_wrreg(chan, S3C2410_DMA_DCON,
-- chan->dcon | reload | (buf->size/chan->xfer_unit));
-+ chan->dcon | S3C2410_DCON_NORELOAD |
-+ (buf->size/chan->xfer_unit));
-
-- chan->next = buf->next;
-+ chan->curr = buf;
-
- /* update the state of the channel */
--
-- switch (chan->load_state) {
-- case S3C2410_DMALOAD_NONE:
-- chan->load_state = S3C2410_DMALOAD_1LOADED;
-- break;
--
-- case S3C2410_DMALOAD_1RUNNING:
-- chan->load_state = S3C2410_DMALOAD_1LOADED_1RUNNING;
-- break;
--
-- default:
-- dmawarn("dmaload: unknown state %d in loadbuffer\n",
-- chan->load_state);
-- break;
-- }
-+ chan->load_state = S3C2410_DMALOAD_1RUNNING;
-
- return 0;
- }
-@@ -343,7 +246,6 @@ static int s3c2410_dma_start(struct s3c2410_dma_chan *chan)
- dbg_showchan(chan);
-
- /* enable the channel */
--
- if (!chan->irq_enabled) {
- enable_irq(chan->irq);
- chan->irq_enabled = 1;
-@@ -358,14 +260,6 @@ static int s3c2410_dma_start(struct s3c2410_dma_chan *chan)
-
- pr_debug("dma%d: %08lx to DMASKTRIG\n", chan->number, tmp);
-
--#if 0
-- /* the dma buffer loads should take care of clearing the AUTO
-- * reloading feature */
-- tmp = dma_rdreg(chan, S3C2410_DMA_DCON);
-- tmp &= ~S3C2410_DCON_NORELOAD;
-- dma_wrreg(chan, S3C2410_DMA_DCON, tmp);
--#endif
--
- s3c2410_dma_call_op(chan, S3C2410_DMAOP_START);
-
- dbg_showchan(chan);
-@@ -375,43 +269,11 @@ static int s3c2410_dma_start(struct s3c2410_dma_chan *chan)
- * the first buffer is finished, the new one will be loaded onto
- * the channel */
-
-- if (chan->next != NULL) {
-- if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
--
-- if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-- pr_debug("%s: buff not yet loaded, no more todo\n",
-- __func__);
-- } else {
-- chan->load_state = S3C2410_DMALOAD_1RUNNING;
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- }
--
-- } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- }
-- }
--
--
- local_irq_restore(flags);
-
- return 0;
- }
-
--/* s3c2410_dma_canload
-- *
-- * work out if we can queue another buffer into the DMA engine
--*/
--
--static int
--s3c2410_dma_canload(struct s3c2410_dma_chan *chan)
--{
-- if (chan->load_state == S3C2410_DMALOAD_NONE ||
-- chan->load_state == S3C2410_DMALOAD_1RUNNING)
-- return 1;
--
-- return 0;
--}
--
- /* s3c2410_dma_enqueue
- *
- * queue an given buffer for dma transfer.
-@@ -460,48 +322,19 @@ int s3c2410_dma_enqueue(enum dma_ch channel, void *id,
-
- local_irq_save(flags);
-
-- if (chan->curr == NULL) {
-- /* we've got nothing loaded... */
-- pr_debug("%s: buffer %p queued onto empty channel\n",
-- __func__, buf);
--
-- chan->curr = buf;
-- chan->end = buf;
-- chan->next = NULL;
-+ if (chan->end == NULL) {
-+ pr_debug("dma%d: queued buffer onto empty channel\n",
-+ chan->number);
-+ chan->next = buf;
-+ chan->end = buf;
- } else {
-- pr_debug("dma%d: %s: buffer %p queued onto non-empty channel\n",
-- chan->number, __func__, buf);
--
-- if (chan->end == NULL) {
-- pr_debug("dma%d: %s: %p not empty, and chan->end==NULL?\n",
-- chan->number, __func__, chan);
-- } else {
-- chan->end->next = buf;
-- chan->end = buf;
-- }
-+ pr_debug("dma%d: queued buffer onto non-empty channel\n",
-+ chan->number);
-+ chan->end->next = buf;
-+ chan->end = buf;
- }
-
-- /* if necessary, update the next buffer field */
-- if (chan->next == NULL)
-- chan->next = buf;
--
-- /* check to see if we can load a buffer */
-- if (chan->state == S3C2410_DMA_RUNNING) {
-- if (chan->load_state == S3C2410_DMALOAD_1LOADED && 1) {
-- if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-- printk(KERN_ERR "dma%d: loadbuffer:"
-- "timeout loading buffer\n",
-- chan->number);
-- dbg_showchan(chan);
-- local_irq_restore(flags);
-- return -EINVAL;
-- }
-- }
--
-- while (s3c2410_dma_canload(chan) && chan->next != NULL) {
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- }
-- } else if (chan->state == S3C2410_DMA_IDLE) {
-+ if (chan->state == S3C2410_DMA_IDLE) {
- if (chan->flags & S3C2410_DMAF_AUTOSTART) {
- s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL,
- S3C2410_DMAOP_START);
-@@ -528,51 +361,6 @@ s3c2410_dma_freebuf(struct s3c2410_dma_buf *buf)
- }
- }
-
--/* s3c2410_dma_lastxfer
-- *
-- * called when the system is out of buffers, to ensure that the channel
-- * is prepared for shutdown.
--*/
--
--static inline void
--s3c2410_dma_lastxfer(struct s3c2410_dma_chan *chan)
--{
--#if 0
-- pr_debug("dma%d: s3c2410_dma_lastxfer: load_state %d\n",
-- chan->number, chan->load_state);
--#endif
--
-- switch (chan->load_state) {
-- case S3C2410_DMALOAD_NONE:
-- break;
--
-- case S3C2410_DMALOAD_1LOADED:
-- if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-- /* flag error? */
-- printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
-- chan->number, __func__);
-- return;
-- }
-- break;
--
-- case S3C2410_DMALOAD_1LOADED_1RUNNING:
-- /* I believe in this case we do not have anything to do
-- * until the next buffer comes along, and we turn off the
-- * reload */
-- return;
--
-- default:
-- pr_debug("dma%d: lastxfer: unhandled load_state %d with no next\n",
-- chan->number, chan->load_state);
-- return;
--
-- }
--
-- /* hopefully this'll shut the damned thing up after the transfer... */
-- dma_wrreg(chan, S3C2410_DMA_DCON, chan->dcon | S3C2410_DCON_NORELOAD);
--}
--
--
- #define dmadbg2(x...)
-
- static irqreturn_t
-@@ -581,57 +369,25 @@ s3c2410_dma_irq(int irq, void *devpw)
- struct s3c2410_dma_chan *chan = (struct s3c2410_dma_chan *)devpw;
- struct s3c2410_dma_buf *buf;
-
-+ /* Check for orphaned irq */
-+ if (chan->state == S3C2410_DMA_IDLE)
-+ return IRQ_HANDLED;
-+
- buf = chan->curr;
-
- dbg_showchan(chan);
-
- /* modify the channel state */
-
-- switch (chan->load_state) {
-- case S3C2410_DMALOAD_1RUNNING:
-- /* TODO - if we are running only one buffer, we probably
-- * want to reload here, and then worry about the buffer
-- * callback */
--
-- chan->load_state = S3C2410_DMALOAD_NONE;
-- break;
--
-- case S3C2410_DMALOAD_1LOADED:
-- /* iirc, we should go back to NONE loaded here, we
-- * had a buffer, and it was never verified as being
-- * loaded.
-- */
--
-+ if (chan->load_state == S3C2410_DMALOAD_1RUNNING)
- chan->load_state = S3C2410_DMALOAD_NONE;
-- break;
--
-- case S3C2410_DMALOAD_1LOADED_1RUNNING:
-- /* we'll worry about checking to see if another buffer is
-- * ready after we've called back the owner. This should
-- * ensure we do not wait around too long for the DMA
-- * engine to start the next transfer
-- */
--
-- chan->load_state = S3C2410_DMALOAD_1LOADED;
-- break;
--
-- case S3C2410_DMALOAD_NONE:
-+ else
- printk(KERN_ERR "dma%d: IRQ with no loaded buffer?\n",
-- chan->number);
-- break;
--
-- default:
-- printk(KERN_ERR "dma%d: IRQ in invalid load_state %d\n",
-- chan->number, chan->load_state);
-- break;
-- }
-+ chan->number);
-
- if (buf != NULL) {
-- /* update the chain to make sure that if we load any more
-- * buffers when we call the callback function, things should
-- * work properly */
--
-- chan->curr = buf->next;
-+ chan->curr = NULL;
-+ chan->next = buf->next;
- buf->next = NULL;
-
- if (buf->magic != BUF_MAGIC) {
-@@ -639,12 +395,10 @@ s3c2410_dma_irq(int irq, void *devpw)
- chan->number, __func__, buf);
- return IRQ_HANDLED;
- }
--
- s3c2410_dma_buffdone(chan, buf, S3C2410_RES_OK);
-
- /* free resouces */
- s3c2410_dma_freebuf(buf);
-- } else {
- }
-
- /* only reload if the channel is still running... our buffer done
-@@ -654,53 +408,36 @@ s3c2410_dma_irq(int irq, void *devpw)
- /* todo: check that when the channel is shut-down from inside this
- * function, we cope with unsetting reload, etc */
-
-- if (chan->next != NULL && chan->state != S3C2410_DMA_IDLE) {
-- unsigned long flags;
--
-- switch (chan->load_state) {
-- case S3C2410_DMALOAD_1RUNNING:
-- /* don't need to do anything for this state */
-- break;
--
-- case S3C2410_DMALOAD_NONE:
-- /* can load buffer immediately */
-- break;
--
-- case S3C2410_DMALOAD_1LOADED:
-- if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-- /* flag error? */
-- printk(KERN_ERR "dma%d: timeout waiting for load (%s)\n",
-- chan->number, __func__);
-- return IRQ_HANDLED;
-- }
--
-- break;
--
-- case S3C2410_DMALOAD_1LOADED_1RUNNING:
-- goto no_load;
--
-- default:
-- printk(KERN_ERR "dma%d: unknown load_state in irq, %d\n",
-- chan->number, chan->load_state);
-- return IRQ_HANDLED;
-- }
-+ if (chan->next != NULL) {
-+ if (chan->state != S3C2410_DMA_IDLE) {
-+ unsigned long flags;
-+ unsigned long tmp;
-
-- local_irq_save(flags);
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- local_irq_restore(flags);
-+ pr_debug("%s: dma%d: continuing with next buffer\n",
-+ __func__, chan->number);
-+ local_irq_save(flags);
-+ s3c2410_dma_loadbuffer(chan, chan->next);
-+ tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-+ tmp &= ~S3C2410_DMASKTRIG_STOP;
-+ tmp |= S3C2410_DMASKTRIG_ON;
-+ dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
-+ local_irq_restore(flags);
-+ } else
-+ pr_debug("dma%d: buffdone callback stopped dma...\n",
-+ chan->number);
- } else {
-- s3c2410_dma_lastxfer(chan);
-+ /* No more buffers? So no queue */
-+ chan->end = NULL;
-
- /* see if we can stop this channel.. */
-- if (chan->load_state == S3C2410_DMALOAD_NONE) {
-- pr_debug("dma%d: end of transfer, stopping channel (%ld)\n",
-+ if (chan->state != S3C2410_DMA_IDLE) {
-+ pr_debug("dma%d: end of transfer, stopping channel (%lu)\n",
- chan->number, jiffies);
- s3c2410_dma_ctrl(chan->number | DMACH_LOW_LEVEL,
- S3C2410_DMAOP_STOP);
- }
- }
-
-- no_load:
- return IRQ_HANDLED;
- }
-
-@@ -839,9 +576,20 @@ static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan)
- s3c2410_dma_call_op(chan, S3C2410_DMAOP_STOP);
-
- tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-- tmp |= S3C2410_DMASKTRIG_STOP;
-- //tmp &= ~S3C2410_DMASKTRIG_ON;
-- dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
-+ if (tmp & S3C2410_DMASKTRIG_ON) {
-+ int retries = 1000;
-+ tmp |= S3C2410_DMASKTRIG_STOP;
-+ dma_wrreg(chan, S3C2410_DMA_DMASKTRIG, tmp);
-+
-+ while (--retries) {
-+ tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
-+ if (!(tmp & S3C2410_DMASKTRIG_ON))
-+ break;
-+ }
-+
-+ if (!retries)
-+ pr_debug("dma%d: failed to stop??\n", chan->number);
-+ }
-
- #if 0
- /* should also clear interrupts, according to WinCE BSP */
-@@ -859,22 +607,6 @@ static int s3c2410_dma_dostop(struct s3c2410_dma_chan *chan)
- return 0;
- }
-
--static void s3c2410_dma_waitforstop(struct s3c2410_dma_chan *chan)
--{
-- unsigned long tmp;
-- unsigned int timeout = 0x10000;
--
-- while (timeout-- > 0) {
-- tmp = dma_rdreg(chan, S3C2410_DMA_DMASKTRIG);
--
-- if (!(tmp & S3C2410_DMASKTRIG_ON))
-- return;
-- }
--
-- pr_debug("dma%d: failed to stop?\n", chan->number);
--}
--
--
- /* s3c2410_dma_flush
- *
- * stop the channel, and remove all current and pending transfers
-@@ -916,8 +648,6 @@ static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan)
-
- dbg_showregs(chan);
-
-- s3c2410_dma_waitforstop(chan);
--
- #if 0
- /* should also clear interrupts, according to WinCE BSP */
- {
-@@ -938,38 +668,8 @@ static int s3c2410_dma_flush(struct s3c2410_dma_chan *chan)
-
- static int s3c2410_dma_started(struct s3c2410_dma_chan *chan)
- {
-- unsigned long flags;
--
-- local_irq_save(flags);
--
-- dbg_showchan(chan);
--
-- /* if we've only loaded one buffer onto the channel, then chec
-- * to see if we have another, and if so, try and load it so when
-- * the first buffer is finished, the new one will be loaded onto
-- * the channel */
--
-- if (chan->next != NULL) {
-- if (chan->load_state == S3C2410_DMALOAD_1LOADED) {
--
-- if (s3c2410_dma_waitforload(chan, __LINE__) == 0) {
-- pr_debug("%s: buff not yet loaded, no more todo\n",
-- __func__);
-- } else {
-- chan->load_state = S3C2410_DMALOAD_1RUNNING;
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- }
--
-- } else if (chan->load_state == S3C2410_DMALOAD_1RUNNING) {
-- s3c2410_dma_loadbuffer(chan, chan->next);
-- }
-- }
--
--
-- local_irq_restore(flags);
--
-+ /* Do nothing */
- return 0;
--
- }
-
- int
-@@ -1040,16 +740,12 @@ int s3c2410_dma_config(enum dma_ch channel,
- case DMACH_PCM_IN:
- case DMACH_PCM_OUT:
- case DMACH_MIC_IN:
-+ case DMACH_SDI:
- default:
- dcon |= S3C2410_DCON_HANDSHAKE;
- dcon |= S3C2410_DCON_SYNC_PCLK;
- break;
-
-- case DMACH_SDI:
-- /* note, ensure if need HANDSHAKE or not */
-- dcon |= S3C2410_DCON_SYNC_PCLK;
-- break;
--
- case DMACH_XD0:
- case DMACH_XD1:
- dcon |= S3C2410_DCON_HANDSHAKE;
-@@ -1224,20 +920,19 @@ static void s3c2410_dma_resume_chan(struct s3c2410_dma_chan *cp)
- {
- unsigned int no = cp->number | DMACH_LOW_LEVEL;
-
-- /* restore channel's hardware configuration */
--
- if (!cp->in_use)
- return;
-
-- printk(KERN_INFO "dma%d: restoring configuration\n", cp->number);
--
-- s3c2410_dma_config(no, cp->xfer_unit);
-- s3c2410_dma_devconfig(no, cp->source, cp->dev_addr);
--
- /* re-select the dma source for this channel */
-
- if (cp->map != NULL)
- dma_sel.select(cp, cp->map);
-+
-+ /* restore channel's hardware configuration */
-+ printk(KERN_INFO "dma%d: restoring configuration\n", cp->number);
-+ s3c2410_dma_config(no, cp->xfer_unit);
-+ s3c2410_dma_devconfig(no, cp->source, cp->dev_addr);
-+
- }
-
- static void s3c2410_dma_resume(void)
-diff --git a/arch/arm/mach-s3c24xx/include/mach/dma.h b/arch/arm/mach-s3c24xx/include/mach/dma.h
-index b55da1d..b207633 100644
---- a/arch/arm/mach-s3c24xx/include/mach/dma.h
-+++ b/arch/arm/mach-s3c24xx/include/mach/dma.h
-@@ -94,28 +94,15 @@ enum s3c2410_dma_state {
- *
- * There are no buffers loaded (the channel should be inactive)
- *
-- * S3C2410_DMA_1LOADED
-- *
-- * There is one buffer loaded, however it has not been confirmed to be
-- * loaded by the DMA engine. This may be because the channel is not
-- * yet running, or the DMA driver decided that it was too costly to
-- * sit and wait for it to happen.
-- *
- * S3C2410_DMA_1RUNNING
- *
-- * The buffer has been confirmed running, and not finisged
-- *
-- * S3C2410_DMA_1LOADED_1RUNNING
-+ * The buffer has been confirmed running, and not finished
- *
-- * There is a buffer waiting to be loaded by the DMA engine, and one
-- * currently running.
- */
-
- enum s3c2410_dma_loadst {
- S3C2410_DMALOAD_NONE,
-- S3C2410_DMALOAD_1LOADED,
- S3C2410_DMALOAD_1RUNNING,
-- S3C2410_DMALOAD_1LOADED_1RUNNING,
- };
-
-
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0002-s3cmci-minor-fixups.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0002-s3cmci-minor-fixups.patch
deleted file mode 100644
index 7bf0163..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0002-s3cmci-minor-fixups.patch
+++ /dev/null
@@ -1,40 +0,0 @@
-From ecbeff382c24f958c2451694041165779312638d Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Fri, 13 Aug 2010 20:01:53 +0300
-Subject: [PATCH 02/12] s3cmci: minor fixups
-
-- It's not necessary to start DMA op manually, as we have
-autostart feature enabled
-- Restore prescaler before DMA operation, otherwise it
-takes ages to complete DMA op.
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- drivers/mmc/host/s3cmci.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
-diff --git a/drivers/mmc/host/s3cmci.c b/drivers/mmc/host/s3cmci.c
-index 8d6794c..d9b11d8 100644
---- a/drivers/mmc/host/s3cmci.c
-+++ b/drivers/mmc/host/s3cmci.c
-@@ -1184,6 +1184,8 @@ static int s3cmci_prepare_dma(struct s3cmci_host *host, struct mmc_data *data)
- sg_dma_address(&data->sg[i]),
- sg_dma_len(&data->sg[i]));
-
-+ /* Restore prescaler value */
-+ writel(host->prescaler, host->base + S3C2410_SDIPRE);
- res = s3c2410_dma_enqueue(host->dma, host,
- sg_dma_address(&data->sg[i]),
- sg_dma_len(&data->sg[i]));
-@@ -1194,8 +1196,6 @@ static int s3cmci_prepare_dma(struct s3cmci_host *host, struct mmc_data *data)
- }
- }
-
-- s3c2410_dma_ctrl(host->dma, S3C2410_DMAOP_START);
--
- return 0;
- }
-
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0003-ARM-s3c2410-drop-RFKILL-driver-for-H1940-bluetooth.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0003-ARM-s3c2410-drop-RFKILL-driver-for-H1940-bluetooth.patch
deleted file mode 100644
index ec81c81..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0003-ARM-s3c2410-drop-RFKILL-driver-for-H1940-bluetooth.patch
+++ /dev/null
@@ -1,200 +0,0 @@
-From c79370dca44c6917b1c7eb7561e736eb85e74a37 Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:09:19 +0300
-Subject: [PATCH 03/12] ARM: s3c2410: drop RFKILL driver for H1940 bluetooth
-
-rfkill-gpio can do it's job easily.
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/Kconfig | 8 --
- arch/arm/mach-s3c24xx/Makefile | 1 -
- arch/arm/mach-s3c24xx/h1940-bluetooth.c | 145 --------------------------------
- 3 files changed, 154 deletions(-)
- delete mode 100644 arch/arm/mach-s3c24xx/h1940-bluetooth.c
-
-diff --git a/arch/arm/mach-s3c24xx/Kconfig b/arch/arm/mach-s3c24xx/Kconfig
-index dba2173..7e125f8 100644
---- a/arch/arm/mach-s3c24xx/Kconfig
-+++ b/arch/arm/mach-s3c24xx/Kconfig
-@@ -307,14 +307,6 @@ config ARCH_H1940
- help
- Say Y here if you are using the HP IPAQ H1940
-
--config H1940BT
-- tristate "Control the state of H1940 bluetooth chip"
-- depends on ARCH_H1940
-- select RFKILL
-- help
-- This is a simple driver that is able to control
-- the state of built in bluetooth chip on h1940.
--
- config PM_H1940
- bool
- help
-diff --git a/arch/arm/mach-s3c24xx/Makefile b/arch/arm/mach-s3c24xx/Makefile
-index 7f54e5b..d326722 100644
---- a/arch/arm/mach-s3c24xx/Makefile
-+++ b/arch/arm/mach-s3c24xx/Makefile
-@@ -65,7 +65,6 @@ obj-$(CONFIG_MACH_AML_M5900) += mach-amlm5900.o
- obj-$(CONFIG_ARCH_BAST) += mach-bast.o
- obj-$(CONFIG_BAST_PC104_IRQ) += bast-irq.o
- obj-$(CONFIG_ARCH_H1940) += mach-h1940.o
--obj-$(CONFIG_H1940BT) += h1940-bluetooth.o
- obj-$(CONFIG_PM_H1940) += pm-h1940.o
- obj-$(CONFIG_MACH_N30) += mach-n30.o
- obj-$(CONFIG_MACH_OTOM) += mach-otom.o
-diff --git a/arch/arm/mach-s3c24xx/h1940-bluetooth.c b/arch/arm/mach-s3c24xx/h1940-bluetooth.c
-deleted file mode 100644
-index 5b98bfd..0000000
---- a/arch/arm/mach-s3c24xx/h1940-bluetooth.c
-+++ /dev/null
-@@ -1,145 +0,0 @@
--/*
-- * arch/arm/mach-s3c2410/h1940-bluetooth.c
-- * Copyright (c) Arnaud Patard <arnaud.patard at rtp-net.org>
-- *
-- * This file is subject to the terms and conditions of the GNU General Public
-- * License. See the file COPYING in the main directory of this archive for
-- * more details.
-- *
-- * S3C2410 bluetooth "driver"
-- *
-- */
--
--#include <linux/module.h>
--#include <linux/platform_device.h>
--#include <linux/delay.h>
--#include <linux/string.h>
--#include <linux/ctype.h>
--#include <linux/leds.h>
--#include <linux/gpio.h>
--#include <linux/rfkill.h>
--
--#include <mach/hardware.h>
--#include <mach/regs-gpio.h>
--
--#include "h1940.h"
--
--#define DRV_NAME "h1940-bt"
--
--/* Bluetooth control */
--static void h1940bt_enable(int on)
--{
-- if (on) {
-- /* Power on the chip */
-- gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 1);
-- /* Reset the chip */
-- mdelay(10);
--
-- gpio_set_value(S3C2410_GPH(1), 1);
-- mdelay(10);
-- gpio_set_value(S3C2410_GPH(1), 0);
--
-- h1940_led_blink_set(-EINVAL, GPIO_LED_BLINK, NULL, NULL);
-- }
-- else {
-- gpio_set_value(S3C2410_GPH(1), 1);
-- mdelay(10);
-- gpio_set_value(S3C2410_GPH(1), 0);
-- mdelay(10);
-- gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 0);
--
-- h1940_led_blink_set(-EINVAL, GPIO_LED_NO_BLINK_LOW, NULL, NULL);
-- }
--}
--
--static int h1940bt_set_block(void *data, bool blocked)
--{
-- h1940bt_enable(!blocked);
-- return 0;
--}
--
--static const struct rfkill_ops h1940bt_rfkill_ops = {
-- .set_block = h1940bt_set_block,
--};
--
--static int h1940bt_probe(struct platform_device *pdev)
--{
-- struct rfkill *rfk;
-- int ret = 0;
--
-- ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev));
-- if (ret) {
-- dev_err(&pdev->dev, "could not get GPH1\n");
-- return ret;
-- }
--
-- ret = gpio_request(H1940_LATCH_BLUETOOTH_POWER, dev_name(&pdev->dev));
-- if (ret) {
-- gpio_free(S3C2410_GPH(1));
-- dev_err(&pdev->dev, "could not get BT_POWER\n");
-- return ret;
-- }
--
-- /* Configures BT serial port GPIOs */
-- s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
-- s3c_gpio_setpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
-- s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
-- s3c_gpio_setpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
-- s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
-- s3c_gpio_setpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
-- s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
-- s3c_gpio_setpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
--
-- rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH,
-- &h1940bt_rfkill_ops, NULL);
-- if (!rfk) {
-- ret = -ENOMEM;
-- goto err_rfk_alloc;
-- }
--
-- ret = rfkill_register(rfk);
-- if (ret)
-- goto err_rfkill;
--
-- platform_set_drvdata(pdev, rfk);
--
-- return 0;
--
--err_rfkill:
-- rfkill_destroy(rfk);
--err_rfk_alloc:
-- return ret;
--}
--
--static int h1940bt_remove(struct platform_device *pdev)
--{
-- struct rfkill *rfk = platform_get_drvdata(pdev);
--
-- platform_set_drvdata(pdev, NULL);
-- gpio_free(S3C2410_GPH(1));
--
-- if (rfk) {
-- rfkill_unregister(rfk);
-- rfkill_destroy(rfk);
-- }
-- rfk = NULL;
--
-- h1940bt_enable(0);
--
-- return 0;
--}
--
--
--static struct platform_driver h1940bt_driver = {
-- .driver = {
-- .name = DRV_NAME,
-- },
-- .probe = h1940bt_probe,
-- .remove = h1940bt_remove,
--};
--
--module_platform_driver(h1940bt_driver);
--
--MODULE_AUTHOR("Arnaud Patard <arnaud.patard at rtp-net.org>");
--MODULE_DESCRIPTION("Driver for the iPAQ H1940 bluetooth chip");
--MODULE_LICENSE("GPL");
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0004-mtd-nand-s3c2410-add-iPAQ-specific-layout.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0004-mtd-nand-s3c2410-add-iPAQ-specific-layout.patch
deleted file mode 100644
index 229baf4..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0004-mtd-nand-s3c2410-add-iPAQ-specific-layout.patch
+++ /dev/null
@@ -1,28 +0,0 @@
-From f89a1a53b00b258aeb44a8511fb4adc657108423 Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Sun, 18 Dec 2011 11:48:46 +0300
-Subject: [PATCH 04/12] mtd: nand: s3c2410: add iPAQ specific layout
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- drivers/mtd/nand/s3c2410.c | 4 ++--
- 1 file changed, 2 insertions(+), 2 deletions(-)
-
-diff --git a/drivers/mtd/nand/s3c2410.c b/drivers/mtd/nand/s3c2410.c
-index d65cbe9..0806e46 100644
---- a/drivers/mtd/nand/s3c2410.c
-+++ b/drivers/mtd/nand/s3c2410.c
-@@ -54,8 +54,8 @@
-
- static struct nand_ecclayout nand_hw_eccoob = {
- .eccbytes = 3,
-- .eccpos = {0, 1, 2},
-- .oobfree = {{8, 8}}
-+ .eccpos = {8, 9, 10},
-+ .oobfree = {{2, 6}, {11, 5}}
- };
-
- /* controller and mtd information */
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0005-ARM-s3c2410-Add-nand-device-for-h1940.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0005-ARM-s3c2410-Add-nand-device-for-h1940.patch
deleted file mode 100644
index f5272be..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0005-ARM-s3c2410-Add-nand-device-for-h1940.patch
+++ /dev/null
@@ -1,114 +0,0 @@
-From d284529e4b6f6001031d8f7d513fd12f84c9d5de Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:13:29 +0300
-Subject: [PATCH 05/12] ARM: s3c2410: Add nand device for h1940
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 62 ++++++++++++++++++++++++++++++++++++++
- 1 file changed, 62 insertions(+)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 74dd479..6f2e979 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -31,6 +31,9 @@
- #include <linux/s3c_adc_battery.h>
- #include <linux/delay.h>
-
-+#include <linux/mtd/mtd.h>
-+#include <linux/mtd/partitions.h>
-+
- #include <video/platform_lcd.h>
-
- #include <linux/mmc/host.h>
-@@ -46,6 +49,7 @@
- #include <linux/platform_data/mmc-s3cmci.h>
- #include <linux/platform_data/touchscreen-s3c2410.h>
- #include <linux/platform_data/usb-s3c2410_udc.h>
-+#include <linux/platform_data/mtd-nand-s3c2410.h>
-
- #include <sound/uda1380.h>
-
-@@ -465,6 +469,62 @@ static struct s3c24xx_mci_pdata h1940_mmc_cfg __initdata = {
- .ocr_avail = MMC_VDD_32_33,
- };
-
-+static struct mtd_partition h1940_nand_part[] = {
-+ [0] = {
-+ .name = "Boot0",
-+ .offset = 0,
-+ .size = SZ_16K,
-+ .mask_flags = MTD_WRITEABLE,
-+ },
-+ [1] = {
-+ .name = "Boot1",
-+ .offset = MTDPART_OFS_APPEND,
-+ .size = SZ_1K * 240,
-+ .mask_flags = 0,
-+ },
-+ [2] = {
-+ .name = "Env",
-+ .offset = MTDPART_OFS_APPEND,
-+ .size = SZ_16K,
-+ .mask_flags = 0,
-+ },
-+ [3] = {
-+ .name = "Opts",
-+ .offset = MTDPART_OFS_APPEND,
-+ .size = SZ_32K,
-+ .mask_flags = 0,
-+ },
-+ [4] = {
-+ .name = "Kernel",
-+ .offset = MTDPART_OFS_APPEND,
-+ .size = SZ_1M * 3,
-+ .mask_flags = 0,
-+ },
-+ [5] = {
-+ .name = "Filesystem",
-+ .offset = MTDPART_OFS_APPEND,
-+ .size = MTDPART_SIZ_FULL,
-+ .mask_flags = 0,
-+ },
-+};
-+
-+static struct s3c2410_nand_set h1940_nand_sets[] = {
-+ [0] = {
-+ .name = "Internal",
-+ .nr_chips = 1,
-+ .nr_partitions = ARRAY_SIZE(h1940_nand_part),
-+ .partitions = h1940_nand_part,
-+ },
-+};
-+
-+static struct s3c2410_platform_nand h1940_nand_info = {
-+ .tacls = 14,
-+ .twrph0 = 44,
-+ .twrph1 = 20,
-+ .nr_sets = ARRAY_SIZE(h1940_nand_sets),
-+ .sets = h1940_nand_sets,
-+};
-+
- static int h1940_backlight_init(struct device *dev)
- {
- gpio_request(S3C2410_GPB(0), "Backlight");
-@@ -632,6 +692,7 @@ static struct platform_device *h1940_devices[] __initdata = {
- &h1940_device_bluetooth,
- &s3c_device_sdi,
- &s3c_device_rtc,
-+ &s3c_device_nand,
- &samsung_device_pwm,
- &h1940_backlight,
- &h1940_lcd_powerdev,
-@@ -676,6 +737,7 @@ static void __init h1940_init(void)
- s3c24xx_udc_set_platdata(&h1940_udc_cfg);
- s3c24xx_ts_set_platdata(&h1940_ts_cfg);
- s3c_i2c0_set_platdata(NULL);
-+ s3c_nand_set_platdata(&h1940_nand_info);
-
- /* Turn off suspend on both USB ports, and switch the
- * selectable USB port to USB device mode. */
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch
deleted file mode 100644
index c967e9f..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0006-ARM-s3c2410-h1940-don-t-touch-UPLLCON.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 6e1b56f2dbb94a1ff320141819bc8cea2462daec Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:15:16 +0300
-Subject: [PATCH 06/12] ARM: s3c2410: h1940: don't touch UPLLCON
-
-It's a bit late to modify UPLLCON in board init,
-anyway bootloader already puts correct value in it.
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 7 -------
- 1 file changed, 7 deletions(-)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 6f2e979..570450d 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -730,8 +730,6 @@ static void __init h1940_reserve(void)
-
- static void __init h1940_init(void)
- {
-- u32 tmp;
--
- s3c24xx_fb_set_platdata(&h1940_fb_info);
- s3c24xx_mci_set_platdata(&h1940_mmc_cfg);
- s3c24xx_udc_set_platdata(&h1940_udc_cfg);
-@@ -746,11 +744,6 @@ static void __init h1940_init(void)
- S3C2410_MISCCR_USBSUSPND0 |
- S3C2410_MISCCR_USBSUSPND1, 0x0);
-
-- tmp = (0x78 << S3C24XX_PLL_MDIV_SHIFT)
-- | (0x02 << S3C24XX_PLL_PDIV_SHIFT)
-- | (0x03 << S3C24XX_PLL_SDIV_SHIFT);
-- writel(tmp, S3C2410_UPLLCON);
--
- gpio_request(S3C2410_GPC(0), "LCD power");
- gpio_request(S3C2410_GPC(1), "LCD power");
- gpio_request(S3C2410_GPC(4), "LCD power");
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0007-ARM-s3c2410-unlock-reset-button-on-H1940.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0007-ARM-s3c2410-unlock-reset-button-on-H1940.patch
deleted file mode 100644
index 69d7857..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0007-ARM-s3c2410-unlock-reset-button-on-H1940.patch
+++ /dev/null
@@ -1,49 +0,0 @@
-From 49f6216e04b0eec38f5f617bcf6ccca625d4e65d Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Sat, 3 Dec 2011 12:12:21 +0300
-Subject: [PATCH 07/12] ARM: s3c2410: unlock reset button on H1940
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 17 +++++++++++++++--
- 1 file changed, 15 insertions(+), 2 deletions(-)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 570450d..642abaf 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -218,9 +218,9 @@ static struct s3c2410fb_mach_info h1940_fb_info __initdata = {
- .gpcup = 0x0000ffff,
- .gpcup_mask = 0xffffffff,
- .gpdcon = 0xaa84aaa0,
-- .gpdcon_mask = 0xffffffff,
-+ .gpdcon_mask = 0xfffffff3,
- .gpdup = 0x0000faff,
-- .gpdup_mask = 0xffffffff,
-+ .gpdup_mask = 0xfffffffd,
- };
-
- static int power_supply_init(struct device *dev)
-@@ -781,6 +781,19 @@ static void __init h1940_init(void)
- gpio_direction_output(S3C2410_GPA(7), 0);
- gpio_direction_output(H1940_LATCH_LED_FLASH, 0);
-
-+ gpio_request(S3C2410_GPD(1), "Reset sense");
-+ gpio_request(S3C2410_GPA(14), "Reset reset");
-+ gpio_request(S3C2410_GPB(6), "Reset lock");
-+ gpio_direction_input(S3C2410_GPD(1));
-+ gpio_direction_output(S3C2410_GPA(14), 0);
-+ if (gpio_get_value(S3C2410_GPD(1)))
-+ gpio_set_value(S3C2410_GPA(14), 0);
-+
-+ gpio_direction_output(S3C2410_GPA(14), 1);
-+ mdelay(100);
-+ gpio_direction_output(S3C2410_GPB(6), 1);
-+ gpio_direction_output(S3C2410_GPB(6), 0);
-+
- i2c_register_board_info(0, h1940_i2c_devices,
- ARRAY_SIZE(h1940_i2c_devices));
- }
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0008-ARM-h1940-add-bluetooth-RF-kill-switch.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0008-ARM-h1940-add-bluetooth-RF-kill-switch.patch
deleted file mode 100644
index ae0842e..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0008-ARM-h1940-add-bluetooth-RF-kill-switch.patch
+++ /dev/null
@@ -1,75 +0,0 @@
-From 71d5095b75b9c6b148bc9029592914c7d7bb3967 Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Sat, 17 Dec 2011 13:14:51 +0300
-Subject: [PATCH 08/12] ARM: h1940: add bluetooth RF kill switch
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 30 ++++++++++++++++++++++++++++++
- 1 file changed, 30 insertions(+)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 642abaf..96c8c91 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -30,6 +30,7 @@
- #include <linux/pda_power.h>
- #include <linux/s3c_adc_battery.h>
- #include <linux/delay.h>
-+#include <linux/rfkill-gpio.h>
-
- #include <linux/mtd/mtd.h>
- #include <linux/mtd/partitions.h>
-@@ -680,6 +681,21 @@ static struct platform_device h1940_dev_buttons = {
- }
- };
-
-+static struct rfkill_gpio_platform_data h1940_bt_rfkill_pdata = {
-+ .name = "h1940-bt",
-+ .reset_gpio = -EINVAL,
-+ .shutdown_gpio = H1940_LATCH_BLUETOOTH_POWER,
-+ .type = RFKILL_TYPE_BLUETOOTH,
-+};
-+
-+static struct platform_device h1940_bluetooth = {
-+ .name = "rfkill_gpio",
-+ .id = 0,
-+ .dev = {
-+ .platform_data = &h1940_bt_rfkill_pdata,
-+ },
-+};
-+
- static struct platform_device *h1940_devices[] __initdata = {
- &h1940_dev_buttons,
- &s3c_device_ohci,
-@@ -700,6 +716,7 @@ static struct platform_device *h1940_devices[] __initdata = {
- &s3c_device_ts,
- &power_supply,
- &h1940_battery,
-+ &h1940_bluetooth,
- };
-
- static void __init h1940_map_io(void)
-@@ -770,6 +787,19 @@ static void __init h1940_init(void)
- gpio_request(H1940_LATCH_SD_POWER, "SD power");
- gpio_direction_output(H1940_LATCH_SD_POWER, 0);
-
-+ /* Configures BT serial port GPIOs */
-+ s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
-+ s3c_gpio_setpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
-+ s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPH1_nRTS0);
-+ s3c_gpio_setpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
-+ s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
-+ s3c_gpio_setpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
-+ s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
-+ s3c_gpio_setpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
-+
-+ gpio_request(S3C2410_GPC(9), "BT reset");
-+ gpio_direction_output(S3C2410_GPC(9), 1);
-+
- platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices));
-
- gpio_request(S3C2410_GPA(1), "Red LED blink");
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0009-rfkill-add-IR-type.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0009-rfkill-add-IR-type.patch
deleted file mode 100644
index 96e91f9..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0009-rfkill-add-IR-type.patch
+++ /dev/null
@@ -1,51 +0,0 @@
-From c21acad16e8a1fc7840f67c272657f8cf7ad81fc Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:19:47 +0300
-Subject: [PATCH 09/12] rfkill: add IR type
-
-Infrared receivers/transmitters can also be disabled,
-so add IR type to rfkill subsystem
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- include/uapi/linux/rfkill.h | 1 +
- net/rfkill/core.c | 4 +++-
- 2 files changed, 4 insertions(+), 1 deletion(-)
-
-diff --git a/include/uapi/linux/rfkill.h b/include/uapi/linux/rfkill.h
-index 058757f..164ec17 100644
---- a/include/uapi/linux/rfkill.h
-+++ b/include/uapi/linux/rfkill.h
-@@ -50,6 +50,7 @@ enum rfkill_type {
- RFKILL_TYPE_GPS,
- RFKILL_TYPE_FM,
- RFKILL_TYPE_NFC,
-+ RFKILL_TYPE_IR,
- NUM_RFKILL_TYPES,
- };
-
-diff --git a/net/rfkill/core.c b/net/rfkill/core.c
-index 1bacc10..5b824f9 100644
---- a/net/rfkill/core.c
-+++ b/net/rfkill/core.c
-@@ -587,7 +587,7 @@ static DEVICE_ATTR_RO(name);
-
- static const char *rfkill_get_type_str(enum rfkill_type type)
- {
-- BUILD_BUG_ON(NUM_RFKILL_TYPES != RFKILL_TYPE_NFC + 1);
-+ BUILD_BUG_ON(NUM_RFKILL_TYPES != RFKILL_TYPE_IR + 1);
-
- switch (type) {
- case RFKILL_TYPE_WLAN:
-@@ -606,6 +606,8 @@ static const char *rfkill_get_type_str(enum rfkill_type type)
- return "fm";
- case RFKILL_TYPE_NFC:
- return "nfc";
-+ case RFKILL_TYPE_IR:
-+ return "ir";
- default:
- BUG();
- }
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0010-rfkill_gpio-add-support-for-inverted-GPIOs.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0010-rfkill_gpio-add-support-for-inverted-GPIOs.patch
deleted file mode 100644
index 61f171c..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0010-rfkill_gpio-add-support-for-inverted-GPIOs.patch
+++ /dev/null
@@ -1,59 +0,0 @@
-From c21cbdcc9bbe7b74a6b28e87f8d3abf4f230d415 Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Thu, 17 Oct 2013 12:20:50 +0300
-Subject: [PATCH 10/12] rfkill_gpio: add support for inverted GPIOs
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- include/linux/rfkill-gpio.h | 2 ++
- net/rfkill/rfkill-gpio.c | 12 ++++++++----
- 2 files changed, 10 insertions(+), 4 deletions(-)
-
-diff --git a/include/linux/rfkill-gpio.h b/include/linux/rfkill-gpio.h
-index 4d09f6e..af54dda 100644
---- a/include/linux/rfkill-gpio.h
-+++ b/include/linux/rfkill-gpio.h
-@@ -37,7 +37,9 @@
- struct rfkill_gpio_platform_data {
- char *name;
- int reset_gpio;
-+ int reset_gpio_inverted;
- int shutdown_gpio;
-+ int shutdown_gpio_inverted;
- const char *power_clk_name;
- enum rfkill_type type;
- void (*gpio_runtime_close)(struct platform_device *);
-diff --git a/net/rfkill/rfkill-gpio.c b/net/rfkill/rfkill-gpio.c
-index fb076cd..3b4848d 100644
---- a/net/rfkill/rfkill-gpio.c
-+++ b/net/rfkill/rfkill-gpio.c
-@@ -53,18 +53,22 @@ static int rfkill_gpio_set_power(void *data, bool blocked)
-
- if (blocked) {
- if (gpio_is_valid(rfkill->pdata->shutdown_gpio))
-- gpio_direction_output(rfkill->pdata->shutdown_gpio, 0);
-+ gpio_direction_output(rfkill->pdata->shutdown_gpio,
-+ rfkill->pdata->shutdown_gpio_inverted);
- if (gpio_is_valid(rfkill->pdata->reset_gpio))
-- gpio_direction_output(rfkill->pdata->reset_gpio, 0);
-+ gpio_direction_output(rfkill->pdata->reset_gpio,
-+ rfkill->pdata->reset_gpio_inverted);
- if (rfkill->pwr_clk && PWR_CLK_ENABLED(rfkill))
- clk_disable(rfkill->pwr_clk);
- } else {
- if (rfkill->pwr_clk && PWR_CLK_DISABLED(rfkill))
- clk_enable(rfkill->pwr_clk);
- if (gpio_is_valid(rfkill->pdata->reset_gpio))
-- gpio_direction_output(rfkill->pdata->reset_gpio, 1);
-+ gpio_direction_output(rfkill->pdata->reset_gpio,
-+ !rfkill->pdata->reset_gpio_inverted);
- if (gpio_is_valid(rfkill->pdata->shutdown_gpio))
-- gpio_direction_output(rfkill->pdata->shutdown_gpio, 1);
-+ gpio_direction_output(rfkill->pdata->shutdown_gpio,
-+ !rfkill->pdata->shutdown_gpio_inverted);
- }
-
- if (rfkill->pwr_clk)
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0011-ARM-h1940-add-IR-switch.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0011-ARM-h1940-add-IR-switch.patch
deleted file mode 100644
index 4ee12fb..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0011-ARM-h1940-add-IR-switch.patch
+++ /dev/null
@@ -1,61 +0,0 @@
-From f2c0263a125f40197d19e6798a655d2cc71a5f2c Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Sun, 18 Dec 2011 11:29:30 +0300
-Subject: [PATCH 11/12] ARM: h1940: add IR switch
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 23 +++++++++++++++++++++++
- 1 file changed, 23 insertions(+)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 96c8c91..6b45688 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -696,6 +696,22 @@ static struct platform_device h1940_bluetooth = {
- },
- };
-
-+static struct rfkill_gpio_platform_data h1940_ir_rfkill_pdata = {
-+ .name = "h1940-ir",
-+ .reset_gpio = -EINVAL,
-+ .shutdown_gpio = S3C2410_GPB(9),
-+ .shutdown_gpio_inverted = 1,
-+ .type = RFKILL_TYPE_IR,
-+};
-+
-+static struct platform_device h1940_irda = {
-+ .name = "rfkill_gpio",
-+ .id = 1,
-+ .dev = {
-+ .platform_data = &h1940_ir_rfkill_pdata,
-+ },
-+};
-+
- static struct platform_device *h1940_devices[] __initdata = {
- &h1940_dev_buttons,
- &s3c_device_ohci,
-@@ -717,6 +733,7 @@ static struct platform_device *h1940_devices[] __initdata = {
- &power_supply,
- &h1940_battery,
- &h1940_bluetooth,
-+ &h1940_irda,
- };
-
- static void __init h1940_map_io(void)
-@@ -797,6 +814,12 @@ static void __init h1940_init(void)
- s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
- s3c_gpio_setpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
-
-+ /* Configure IR serial port GPIOs */
-+ s3c_gpio_cfgpin(S3C2410_GPH(6), S3C2410_GPH6_TXD2);
-+ s3c_gpio_setpull(S3C2410_GPH(6), S3C_GPIO_PULL_NONE);
-+ s3c_gpio_cfgpin(S3C2410_GPH(7), S3C2410_GPH7_RXD2);
-+ s3c_gpio_setpull(S3C2410_GPH(7), S3C_GPIO_PULL_NONE);
-+
- gpio_request(S3C2410_GPC(9), "BT reset");
- gpio_direction_output(S3C2410_GPC(9), 1);
-
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/0012-ARM-h1940-increase-oversampling-shift.patch b/recipes-kernel/linux/linux-yocto-dev/h1940/0012-ARM-h1940-increase-oversampling-shift.patch
deleted file mode 100644
index b5f9fc0..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/0012-ARM-h1940-increase-oversampling-shift.patch
+++ /dev/null
@@ -1,29 +0,0 @@
-From e54bcd58d416162f8cb1b191c7cff81ecd660137 Mon Sep 17 00:00:00 2001
-From: Vasily Khoruzhick <anarsoul at gmail.com>
-Date: Sun, 18 Dec 2011 11:47:03 +0300
-Subject: [PATCH 12/12] ARM: h1940: increase oversampling shift
-
-4 samples seems to be not enough for touchscreen driver
-to work accurately
-
-Signed-off-by: Vasily Khoruzhick <anarsoul at gmail.com>
----
- arch/arm/mach-s3c24xx/mach-h1940.c | 2 +-
- 1 file changed, 1 insertion(+), 1 deletion(-)
-
-diff --git a/arch/arm/mach-s3c24xx/mach-h1940.c b/arch/arm/mach-s3c24xx/mach-h1940.c
-index 6b45688..ca54dea 100644
---- a/arch/arm/mach-s3c24xx/mach-h1940.c
-+++ b/arch/arm/mach-s3c24xx/mach-h1940.c
-@@ -181,7 +181,7 @@ static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
- static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = {
- .delay = 10000,
- .presc = 49,
-- .oversampling_shift = 2,
-+ .oversampling_shift = 5,
- .cfg_gpio = s3c24xx_ts_cfg_gpio,
- };
-
---
-1.8.4
-
diff --git a/recipes-kernel/linux/linux-yocto-dev/h1940/defconfig b/recipes-kernel/linux/linux-yocto-dev/h1940/defconfig
deleted file mode 100644
index 6565dd5..0000000
--- a/recipes-kernel/linux/linux-yocto-dev/h1940/defconfig
+++ /dev/null
@@ -1,200 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_IKCONFIG=y
-CONFIG_IKCONFIG_PROC=y
-CONFIG_LOG_BUF_SHIFT=18
-CONFIG_CGROUPS=y
-CONFIG_CGROUP_DEBUG=y
-CONFIG_CGROUP_FREEZER=y
-CONFIG_CGROUP_DEVICE=y
-CONFIG_CPUSETS=y
-CONFIG_CGROUP_CPUACCT=y
-CONFIG_RESOURCE_COUNTERS=y
-CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
-# CONFIG_MEMCG_SWAP_ENABLED is not set
-CONFIG_MEMCG_KMEM=y
-CONFIG_CGROUP_SCHED=y
-CONFIG_BLK_CGROUP=y
-# CONFIG_UTS_NS is not set
-# CONFIG_IPC_NS is not set
-# CONFIG_PID_NS is not set
-# CONFIG_NET_NS is not set
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_CC_OPTIMIZE_FOR_SIZE=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_BSD_DISKLABEL=y
-# CONFIG_EFI_PARTITION is not set
-# CONFIG_IOSCHED_DEADLINE is not set
-# CONFIG_IOSCHED_CFQ is not set
-CONFIG_ARCH_S3C24XX=y
-CONFIG_S3C_LOWLEVEL_UART_PORT=1
-CONFIG_SAMSUNG_GPIO_EXTRA=16
-CONFIG_S3C24XX_PWM=y
-CONFIG_CPU_S3C2442=y
-CONFIG_S3C24XX_DMA=y
-CONFIG_ARCH_H1940=y
-CONFIG_PREEMPT_VOLUNTARY=y
-CONFIG_AEABI=y
-# CONFIG_OABI_COMPAT is not set
-# CONFIG_COMPACTION is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CPU_IDLE=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
-CONFIG_APM_EMULATION=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_MULTICAST=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_LRO is not set
-# CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRTTY_SIR=m
-CONFIG_BT=m
-CONFIG_BT_RFCOMM=m
-CONFIG_BT_RFCOMM_TTY=y
-CONFIG_BT_BNEP=m
-CONFIG_BT_HCIUART=m
-CONFIG_BT_HCIUART_H4=y
-CONFIG_BT_HCIUART_BCSP=y
-CONFIG_BT_HCIUART_ATH3K=y
-CONFIG_BT_HCIUART_LL=y
-CONFIG_CFG80211=m
-CONFIG_CFG80211_WEXT=y
-CONFIG_MAC80211=m
-CONFIG_RFKILL=m
-CONFIG_RFKILL_GPIO=m
-CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-# CONFIG_FIRMWARE_IN_KERNEL is not set
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_JEDECPROBE=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_CFI_AMDSTD=y
-CONFIG_MTD_ROM=y
-CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_S3C2410=y
-CONFIG_MTD_NAND_S3C2410_HWECC=y
-CONFIG_BLK_DEV_LOOP=y
-CONFIG_BLK_DEV_RAM=y
-CONFIG_BLK_DEV_RAM_COUNT=1
-CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_NETDEVICES=y
-# CONFIG_ETHERNET is not set
-# CONFIG_INPUT_MOUSEDEV_PSAUX is not set
-CONFIG_INPUT_MOUSEDEV_SCREEN_X=240
-CONFIG_INPUT_MOUSEDEV_SCREEN_Y=320
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_TOUCHSCREEN_S3C2410=y
-# CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_SAMSUNG=y
-CONFIG_SERIAL_SAMSUNG_CONSOLE=y
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-# CONFIG_I2C_COMPAT is not set
-CONFIG_I2C_CHARDEV=m
-CONFIG_I2C_S3C2410=m
-CONFIG_GPIO_SYSFS=y
-CONFIG_POWER_SUPPLY=y
-CONFIG_PDA_POWER=y
-CONFIG_APM_POWER=y
-CONFIG_BATTERY_S3C_ADC=y
-# CONFIG_HWMON is not set
-CONFIG_WATCHDOG=y
-CONFIG_S3C2410_WATCHDOG=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_DUMMY=y
-CONFIG_FB=y
-CONFIG_FB_S3C2410=y
-CONFIG_BACKLIGHT_LCD_SUPPORT=y
-CONFIG_LCD_CLASS_DEVICE=y
-CONFIG_LCD_PLATFORM=y
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-# CONFIG_BACKLIGHT_GENERIC is not set
-CONFIG_BACKLIGHT_PWM=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_SOUND=m
-CONFIG_SND=m
-CONFIG_SND_MIXER_OSS=m
-CONFIG_SND_PCM_OSS=m
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-CONFIG_SND_SOC=m
-CONFIG_SND_SOC_SAMSUNG=m
-CONFIG_SND_SOC_SAMSUNG_H1940_UDA1380=m
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_VBUS_DRAW=250
-CONFIG_USB_S3C2410=y
-CONFIG_USB_ETH=y
-CONFIG_MMC=y
-CONFIG_MMC_UNSAFE_RESUME=y
-CONFIG_MMC_S3C=y
-CONFIG_MMC_S3C_DMA=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_GPIO=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_RTC_CLASS=y
-# CONFIG_RTC_INTF_PROC is not set
-CONFIG_RTC_DRV_S3C=y
-CONFIG_STAGING=y
-# CONFIG_IOMMU_SUPPORT is not set
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=m
-# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
-CONFIG_FUSE_FS=m
-CONFIG_VFAT_FS=y
-CONFIG_FAT_DEFAULT_CODEPAGE=866
-CONFIG_FAT_DEFAULT_IOCHARSET="utf8"
-CONFIG_TMPFS=y
-CONFIG_NFS_FS=y
-CONFIG_NFS_V4=y
-CONFIG_ROOT_NFS=y
-CONFIG_NLS_DEFAULT="utf8"
-CONFIG_NLS_CODEPAGE_866=y
-CONFIG_NLS_CODEPAGE_1251=y
-CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_FS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_USER=y
-CONFIG_CRYPTO_CBC=y
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_MD5=y
-CONFIG_CRYPTO_MICHAEL_MIC=y
-CONFIG_CRYPTO_ARC4=y
-CONFIG_CRYPTO_DES=y
-CONFIG_CRYPTO_ANSI_CPRNG=y
-CONFIG_CRC_CCITT=y
-CONFIG_CRC16=y
-CONFIG_XZ_DEC_X86=y
-CONFIG_XZ_DEC_POWERPC=y
-CONFIG_XZ_DEC_IA64=y
-CONFIG_XZ_DEC_SPARC=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
--
1.9.1
More information about the Openembedded-devel
mailing list