[oe-issues] [Bug 1986] New: Orinoco drivers loading instead of hostap

[bugzilla-daemon at tinman.treke.net]

http://bugs.openembedded.org/show_bug.cgi?id=1986

           Summary: Orinoco drivers loading instead of hostap
           Product: Openembedded
           Version: Angstrom
          Platform: ARM
        OS/Version: All
            Status: NEW
          Severity: normal
          Priority: P2
         Component: Build
        AssignedTo: openembedded-issues at lists.openembedded.org
        ReportedBy: jerry at weareburgess.net
         QAContact: tinderbox-oe at gmx.net


On a Angstrom.2007.1 for spitz built yesterday, using Ambicom WL1100 card,
orinoco drivers are loading. However card does work. If I remember correctly
monitor mode is problematic with the orinoco drivers. If I remove the orinoco
modules (old work around for oz354x) WEP no longer works. When I flash OZ
3.5.4.2rc2 it loads the hostap drivers without removing orinoco modules.

Below is dmessg from insert with orinoco modules removed:

<5>pccard: PCMCIA card inserted into slot 1
<5>pcmcia: registering new device pcmcia1.0
<7>hostap_cs: setting Vcc=33 (constant)
<7>Checking CFTABLE_ENTRY 0x01 (default 0x01)
<7>IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
<7>io->flags = 0x0046, io.base=0x0000, len=64
<6>hostap_cs: Registered netdevice wifi0
<4>pcmcia: request for exclusive IRQ could not be fulfilled.
<4>pcmcia: the driver needs updating to supported shared IRQ lines.
<6>hostap_cs: index 0x01: , irq 137, io 0xc4840000-0xc484003f
<7>prism2_hw_init: initialized in 200 ms
<6>wifi0: NIC: id=0x801b v1.0.0
<6>wifi0: PRI: id=0x15 v1.1.1
<6>wifi0: STA: id=0x1f v1.8.0
<7>wifi0: registered netdevice wlan0
<7>ieee80211_crypt: registered algorithm 'WEP'
<7>ieee80211_crypt_wep: could not allocate crypto API arc4
<4>wlan0: could not initialize WEP: load module hostap_crypt_wep.o
<7>prism2: wlan0: operating mode changed 3 -> 2
<7>wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
<7>   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
<7>   A1=00:00:00:00:00:00 A2=00:10:7a:58:cf:ee A3=ff:ff:ff:ff:ff:ff
A4=00:00:00:00:00:00
<7>wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
<7>   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
<7>   A1=00:00:00:00:00:00 A2=00:10:7a:58:cf:ee A3=ff:ff:ff:ff:ff:ff
A4=00:00:00:00:00:00
<7>wifi0: TXEXC - status=0x0004 ([Discon]) tx_control=000c
<7>   retry_count=0 tx_rate=0 fc=0x0108 (Data::0 ToDS)
<7>   A1=00:00:00:00:00:00 A2=00:10:7a:58:cf:ee A3=ff:ff:ff:ff:ff:ff
A4=00:00:00:00:00:00
<7>wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
<7>wifi0: hfa384x_cmd_issue - timeout - reg=0x8888
<7>wifi0: hfa384x_cmd_issue: cmd reg was busy for 5000 usec
<7>wifi0: hfa384x_cmd_issue - timeout - reg=0x8888
<7>wifi0: hfa384x_cmd: entry still in list? (entry=c3969520, type=0, res=-1)
<7>wifi0: hfa384x_cmd: interrupted; err=-110
<7>wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd51, len=6)
<5>pccard: card ejected from slot 1


-- 
Configure bugmail: http://bugs.openembedded.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.