[Bug 3161] h5000: WiFi doesn't work

[bugzilla-daemon at treke.net]

http://bugs.openembedded.net/show_bug.cgi?id=3161


Klaus Strebel <klaus.strebel at gmx.net> changed:

           What    |Removed                     |Added
----------------------------------------------------------------------------
                 CC|                            |klaus.strebel at gmx.net




--- Comment #29 from Klaus Strebel <klaus.strebel at gmx.net>  2008-03-26 22:00:18 ---
Ok, my FritzBox shows connected, 81% quality, iwconfig says:
wlan0     IEEE 802.11b  ESSID:"FRITZ!Boxxxxxxxxxxx"
          Mode:Managed  Frequency:2.437 GHz  Access Point: 00:04:0E:A3:C4:A1
          Bit Rate:11 Mb/s   Tx-Power=15 dBm
          Retry limit:8   RTS thr=1536 B   Fragment thr=1536 B
          Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX   Security mode:open
          Power Management:off
          Link Quality:57/100  Signal level=59/100
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
but ifup results in:
ifconfig wlan0
wlan0     Link encap:Ethernet  HWaddr 00:02:8A:3A:74:EA
          UP BROADCAST RUNNING  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:1980 (1.9 KiB)

root at pdakst:~$ ifup wlan0
udhcpc (v1.2.1) started
Sending discover...
Sending discover...
[42689.660000] samcop usb host samcop usb host: alloc_safe_buffer: could not
al)[42689.660000] samcop usb host samcop usb host: map_single: unable to map
unsaf!Sending discover...
[42692.730000] samcop usb host samcop usb host: alloc_safe_buffer: could not
al)[42692.730000] samcop usb host samcop usb host: map_single: unable to map
unsaf!No lease, failing.

:-(
Some dmesg output:

[42519.790000] Atmel at76x USB Wireless LAN Driver 0.17 loading
[42519.800000] usbcore: registered new interface driver at76_usb

[42520.330000] usb 1-1: new full speed USB device using samcop u2[42520.510000]
usb 1-1: configuration #1 chosen from 1 choice
[42520.670000] wlan0: USB 1-1:1.0, MAC 00:02:8a:3a:74:ea, firmware 0.100.5-39
[42520.680000] wlan0: regulatory domain 0x41: MKK1 (Japan)
[42524.270000] samcop usb host samcop usb host: alloc_safe_buffer: could not
al)[42524.270000] samcop usb host samcop usb host: map_single: unable to map
unsaf![42526.340000] samcop usb host samcop usb host: alloc_safe_buffer: could
not al)[42526.340000] samcop usb host samcop usb host: map_single: unable to
map unsaf![42529.510000] samcop usb host samcop usb host: alloc_safe_buffer:
could not al)[42529.520000] samcop usb host samcop usb host: map_single: unable
to map unsaf!

Question: how is the regulatory domain set ( the Berlios driver has a tool for
that, i think ). Seems like the device is sending, but not receiving ?!?

Ciao
Klaus


-- 
Configure bugmail: http://bugs.openembedded.net/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug.